background image

5

TIMER SETTING

Under the ON/OFF state, press TIMER to set TIMER OFF/ON.

S

TIMER ON mode: Press TIMER and the LCD displays

xx.x hour, with “hour” blinking. Press 

 or 

 to adjust the

timing value. Next, press ENTER/CANCEL to confirm.

S

TIMER OFF mode: Press TIMER, if LCD does not
display xx.x hour, it means the timer setting was cancelled
(Fig. 11 displays the TIMER OFF setting, under the ON
state).

Fig. 11

 - 

Timer off Setting under the unit’s ON state

Timer range: 0.5−24 hours

Every press of 

 or 

 increases or decreases the set time by 0.5 hour, If either of the arrows are pressed continuously, the set time will

increase or decrease by 0.5 hour ever 0.5 seconds.

SWING MODE

S

SWING ON: Press FUNCTION under the unit’s ON state

to activate the SWING function and 

 blinks. Next, press

ENTER/CANCEL to confirm.

S

SWING OFF: When the SWING function is on, press

FUNCTION to enter the SWING setting interface 

. Next,

press ENTER/CANCEL to cancel the function (see Fig. 12).

Fig. 12

 - 

Swing mode

NOTES:

The SLEEP, TURBO or BLOW mode is the same as the SWING mode.
After the setting is made, the user must press ENTER/CANCEL to revert to the setting status or the unit stops operating automatically
five seconds later.

Содержание KSACN0301AAA











Отзывы: