background image

6

SLEEP MODE

S

SLEEP ON: Press FUNCTION under the unit’s ON
state until the unit enters the SLEEP mode. Press
ENTER/CANCEL to confirm.

S

SLEEP OFF: When the SLEEP  function is activated,
press FUNCTION to enter the SLEEP mode. Next, press
ENTER\CANCEL to exit the function.

In the COOLING  or  DRY  modes, the temperature increases by
1.8

_

F (1

_

C) after the unit runs under the SLEEP mode for 1 hour

and 1.8

_

F (1

_

C) after another hour. Afterwards, the unit will

continue to run at this temperature.

In the HEATING mode, the temperature decreases by 1.8

_

F (1

_

C)

after the unit runs under SLEEP 1 for one hour and 1.8

_

F (1

_

C) after

another hour. Afterwards, the unit runs at this temperature (see Fig.
13).

Fig. 13

 - 

Sleep mode

TURBO SETTING

S

TURBO: The unit on the high fan speed generates quick
cooling or heating so the room temperature can quickly
approach the setting value.

In the COOLING or HEATING mode press FUNCTION until
the unit enters the TURBO mode then press ENTER/CANCEL to
confirm.

When the TURBO function is activated, press FUNCTION  to
enter the TURBO  mode and then press ENTER/CANCEL  to
cancel (see Fig. 14).

Fig. 14

 - 

Turbo mode

Содержание KSACN0301AAA











Отзывы: