21
EN
htr
Enabled or disables HOLD-TO-RUN function
On: HOLD-TO-RUN function.
The pressure of the OPENS/CLOSES button must be maintained throughout the entire manoeuvre.
The opening of the STOP input stops the motor. All the safety inputs are deactivated, except for
the Limit switch inputs /SW01/SW02/SWC1/SWC2).
Off: Automatic/semiautomatic function
(OFF)
1mot
The operating mode with 1 or 2 motors is selected:
On: The motor operation is synchronised. This function must be used in the following cases:
- for each single motor, connect it to M1: Terminals 1/2.
- for two synchronised motors (e.g. balancing doors), connect one motor to M1: terminals 1/2
and the other to M2: terminals 3/4. Adjust the parameters related to motor 1, the M2 limit switch
inputs are deactivated. TDMO and TDMC must be 0.
Off: For two non-synchronised motors, e.g. overlapping gate leaves, adjust TDMO and TDMC
on the desired values.
(OFF)
mloc
Selects the type of electric lock used.
On: Magnetic electric lock, normally fed at 12Vdc.
Power is cut off to the electric lock output before each opening and closing operation.
Off: Electric lock with latch, normally not fed.
Before each opening manoeuvre power is fed at 12Vdc for the time set by the parameter TLOC.
(OFF)
BB
Activates or deactivates the push in closing function. Only with logic SLD:ON
On: The last second of the manoeuvre in closing phase is carried out at normal speed (disabling
slowing) to favour a better hook of the electric lock.
Off: Function disabled.
(OFF)
TST1
Enables or disables checking of photocells on PHOT input, active both in closing and in opening.
On: Check enabled. If the check has a negative result, no manoeuvre is commanded. See Fig.3
- “PHOTO TEST”.
Off: Checking of photocells disabled at each manoeuvre.
(OFF)
TST2
Enables or disables checking of photocells on PHOT inputs, active only in closing.
On: Check enabled. If the check has a negative result, no manoeuvre is commanded. See Fig.3
- “PHOTO TEST”.
Off: Checking of photocells disabled at each manoeuvre.
(OFF)
TSTm
Enables or disables motors check.
On: Check enabled. If the check has a negative result, no manoeuvre is commanded.
Off: Check disabled.
(OFF)
rem
(Enables or disables remote radiotransmitters learning, as indicated in the paragraph “Remote
transmitters learning”.
On: Remote learning enabled.
Off: Remote learning not enabled.
(OFF)
CAUTION:
Any change to one of these parameters/logic:
SPD1 - SPD2 - SLD1 - SLD2 -TSM1 - TSM2 - SOFT
involves a complete operation at reduced speed.
The PRG message is displayed.
5.3) RADIO (
RAD
)
MENU
FUNZIONE
PP
By selecting this function, the receiver goes in waiting (
Push
) for a transmitter code to assign to the step-step function.
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised and the message
OK
is displayed
If the code is not valid, the message
Err
is displayed
2Ch
By selecting this function, the receiver goes into waiting (
Push
) for a transmitter code to assign to the second radio channel.
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised ad the
OK
message is displayed
If the code is not valid, the message
Err
is displayed.
ped
By selecting this function, the receiver goes into waiting (
Push
) for a transmitter code to assign to the pedestrian opening function (see
parameter TPED).
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised ad the
OK
message is displayed
If the code is not valid, the message
Err
is displayed.
CLR
By selecting this function, the receiver goes into waiting (
Push
) for a transmitter code to erase from the memory.
If the code is valid, it is erased and the message
OK
is displayed
If the code is not valid or not present in memory, the message
Err
is displayed
RTR
Completely erases memory of the receiver. Confirmation of the operation is requested.
By selecting this function the receiver goes into waiting (
Push
) for a new PGM pressure to confirm the operation.
At end of erasing the
OK
message is displayed
5.4) CYCLES NUMBER (
NMAN
)
Displays the number of complete cycles (open+close) carried out by the automation.
When the <PG> button is pressed for the first time, it displays the first 4 figures, the second time it shows the last 4. Example <PG>
0012
>>> <PG>
3456
: made 123.456 cycles.
