BYOC Overdrive 2 Скачать руководство пользователя страница 4

Страница: 4 / 37

Parts Checklist for BYOC Overdrive 2

Resistors:

1 - 100ohm (brown/black/black/black/brown)

1 - 220ohm (red/red/black/black/brown)
1 - 470ohm (yellow/purple/black/black/brown)
3 - 1k (brown/black/black/brown/brown)

2 - 4.7k (yellow/purple/black/brown/brown)
8 - 10k (brown/black/black/red/brown)

1 - 100k (brown/black/black/orange/brown)
2 - 511k (green/brown/brown/orange/brown)

2 - 1M (brown/black/black/yellow/brown) or (brown/black/green/gold)

Capacitors

1 - 51pf ceramic disc (small orange cap)

1 - .022µf/22n film (223)

2 - 0.047µf/47n film (473)

2 - 0.1µf/100n film (104)

1 - 0.15µf/150n film (154)
2 - 1µf/1µ0 film (105 or 1J63)

2 - 10µf aluminum electrolytic

1 - 47µf aluminum electrolytic

1 - 100µf aluminum electrolytic

2 - 0.15µf tantalum (154)

2 - 0.22µf tantalum (225)

Diodes:

2 - 1N914 or 1N4148 (small orange glass)

2 - 3mm red LED

Transistors:

3 - MPSA18

(or 2N3904)

Potentiometers: Be sure to snap off the small tab on the side of each panel mounted

pot.

Содержание Overdrive 2





































Результаты поиска

Содержание Overdrive 2

Отзывы:

Похожие инструкции для Overdrive 2

Бренды по названию

Популярные бренды

BYOC Overdrive 2, Инструкции к набору

Результаты поиска

Содержание Overdrive 2

Отзывы:

Похожие инструкции для Overdrive 2

Бренды по названию

Популярные бренды