BYOC Overdrive 2 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 37

background image

Adjusting the Trimpots

All three trimpots affect the gain of the circuit, so all 3 trimpots are extremely interactive,

especially the MIN and MAX trimmers.

MIN trimmer

: This trimmer will affect the amount of minimum distortion. Originally it

was a 51k resistors, so setting this trimpot to exactly halfway will give you stock TS808

specs. Turning it up will give you more drive, turning it down will give you less drive.

MAX trimmer:

This trimmer will affect the amount of maximum distortion. Originally it

was a 4.7k resistor, so setting this trimpot to exactly halfway will give you stock TS808

specs. Turning it up will give you more drive, turning it down will give you less drive.

«
...
28
29
30
31
32
...
»

Содержание Overdrive 2






































Отзывы:

Нет отзывов

Похожие инструкции для Overdrive 2

Бренд: Rane Страницы: 18

Бренд: Rane Страницы: 24

Бренд: Mackie Страницы: 4

Бренд: Christie Страницы: 63

Бренд: OPFXS Страницы: 2

Бренд: BMF Effects Страницы: 2

Бренд: Fishman Страницы: 16

Бренд: Behringer Страницы: 6

Бренд: PhDsolutions Страницы: 15

Бренд: Ibiza sound Страницы: 24

Бренд: Acnodes Страницы: 20

Бренд: Eclectro-Harmonix Страницы: 6

Бренд: DIYRE Страницы: 12

Бренд: Rane Страницы: 6

Бренд: Gemini Страницы: 26

Бренд: D.A.S. Страницы: 27

Бренд: Solid State Logic Страницы: 70

Бренд: YORKVILLE Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды