BW Broadcast DSPXtra-FM страница 50 Скачать руководство пользователя

Страница: 50 / 63

Remote Control Application

SCHEDULING WITH THE REMOTE APPLICATION

Using the menu tree to change the processing is quite simple and really doesn't need a lot of explanation. The

scheduling screens that controls the dayparting may appear daunting so we are going to give you a quick guide

to using it. There are three menu locations for controlling scheduling. The first location is shown in the screen

shot below and it contains the ON/OFF and time setting control. The two menu locations below it access two

banks of four dayparts which make up the 8 dayparts contained in the DSPXtra-FM.

On the daypart windows you have four dayparts. Each has three parameters. The left hand box contains the

name of the preset that you want this daypart to switch to. This box also has the ability to turn the daypart OFF

by clicking down on the arrows until you reach the off option. If off is currently selected you can click up to rotate

through the user and factory presets. The middle box contains the time and day that the daypart will start at. To

select day, hour or minute click on the appropriate part of the box before using the up and down arrows. The day

part of the time also has an ALL option. This means that the daypart will occur on every day. The right most box

contains the length of the daypart in hours and minutes. Like the start time of the daypart you will need to click

into the appropriate part of the box before clicking the up/down arrows.

Scheduling

Содержание DSPXtra-FM
































































Результаты поиска

Содержание DSPXtra-FM

Отзывы:

Похожие инструкции для DSPXtra-FM

Бренды по названию

Популярные бренды

BW Broadcast DSPXtra-FM, Руководство по эксплуатации

Результаты поиска

Содержание DSPXtra-FM

Отзывы:

Похожие инструкции для DSPXtra-FM

Бренды по названию

Популярные бренды