manualshive.com logo in svg

BVL V-LOAD Cutter Megastar 110, Руководство по эксплуатации, Страница: 63 / 88

Поделиться
Скачать
BVL V-LOAD Cutter Megastar 110 Скачать руководство пользователя страница 63

 

 

 

 

WARNING 

 

Danger of falling when hitching a ride on the accessory 
equipment! 

Hitching a ride on the accessory equipment is prohibited. 

Never use the accessory equipment as a lifting platform for 
individuals. 

 

 

  1.  Do not lift up the accessory equipment higher than necessary. 

When using a telescopic loader, retract the telescopic arm 
completely. 

  2.  Lower the hydraulic lifting frame (option). 

  3.  Move the hydraulic side shift (option) to the center position. 

  4.  When driving without loads, move the cutting bar to the 

bottommost position in order to cover the fork tines. 
While driving with a loaded silage block, set the cutting bar  
10-15 cm above the fork tines.  

  5.  Switch off the oil circuit between tractor and accessory 

equipment and the control panel in order to prevent the 
accessory equipment from being operated by accident during 
travel. 

  6.  If the lighting system of the tractor is covered by the accessory 

equipment, a lighting beam must be fitted to the accessory 
equipment and connected to the tractor prior to travel on public 
roadways. Check the lighting beam for proper operation. 

  2.  When traveling with a loaded silage block, drive slowly in order 

not to lose any portion of the load and to protect the silage block 
against deformation. Avoid abrupt steering maneuvers as well as 
sudden start and braking. 

 
 

Содержание V-LOAD Cutter Megastar 110

























































































Отзывы:

Нет отзывов