background image

_

 11 

_

Recommended Oil Type

Only use a two-stroke engine oil formulated for use in high-performance, air-cooled two-stroke engines.

IMPORTANT:  Do not use two-stroke oil intended for water cooled outboard motors. This type of 

two-stroke engine oil does not have the additives for air-cooled two-stroke engines 

and can cause engine damage.

Do not use automotive motor oil. This type of oil does not have the proper additives 

for air-cooled two-stroke engines and can cause engine damage.

Recommended Fuel Type

Use clean, unleaded petrol with an octane rating of 85 or higher. Use of unleaded petrol results in fewer 
combustion chamber deposits and longer spark plug life. Use of premium grade fuel is not necessary or 
recommended.

IMPORTANT: Never use gasohol or alcohol blended fuels in this engine.

Mixing Petrol and Oil

IMPORTANT:  The engine used on this Pruner is of a two-stroke design. The internal

 

moving 

parts of the engine, i.e., crankshaft bearings, piston pin bearings and piston to 

cylinder wall contact surfaces, require oil mixed with the petrol for lubrication.

Failure to add oil to the petrol or failure to mix oil with the petrol at the appropriate 

ratio will

 

cause major engine damage which will void your warranty.

Fuel Mixture Chart

Mixing Instructions

IMPORTANT: Never mix petrol and oil directly in the Pruner fuel tank.

1. Always mix fuel and oil in a clean container approved for petrol.
2. Mark the container to identify it as fuel mix for the Pruner.

3. Use regular unleaded petrol and fill the container with half the required amount of petrol.

4. Pour the correct amount of oil into the container then add the remaining amount of petrol.

5. Close the container tightly and shake it momentarily to evenly mix the oil and the petrol before filling the 

tank on the Pruner.

6. When refilling the Pruner fuel tank, clean around the fuel tank cap to stop dirt and debris from entering 

the tank during cap removal.

7. Always shake the premix fuel container momentarily before filling the fuel tank.

8. Always use a spout or funnel when fueling to reduce fuel spillage.

9. Fill the tank only to within 10mm from the top of the tank. Avoid filling to the top of the tank filler neck.

Petrol

Two-stroke oil

50:1

25:1

ISO-L-EGC/ EGD ,JASO class FC/ FD,

or equivalent two-stroke oil 

ISO-L-EGB , JASO class FB,

or equivalent two-stroke oil

1 litre  

20 mL

40 mL

2 litres

40 mL

80 mL

5 litres

100 mL

200 mL

Содержание TPS261

























Отзывы: