Bushranger TPS261 Скачать руководство пользователя

Страница: 8 / 24

＿

Guide bar and saw chain installation

1. Slot the saw chain in the groove of the guide bar, ensuring

that the cutter section of the saw chain is facing the front.

2. Engage the saw chain into the sprocket.
3. Insert the groove of the guide bar into the pruner’s main

unit and adjust the regulating screw to ensure that the ad-

juster is inserted in the circular hole of the guide bar.

4. Put the chain cover on and temporarily screw it in place

using a nut, to the extent that the guide bar can be moved.

5. Lift up the leading edge of the guide bar and using a screw

driver turn the regulating screw clockwise to tighten the

saw chain until the saw chain slightly touches the lower

side of the guide bar.

6. Securely tighten the nut on the chain cover, using the box

spanner, provided as an accessory with the product.

7. Verify that the saw chain on the central section of the

guide bar can be lifted by the fingers 3 to 4 mm off the

guide bar.

CAUTION

・

In order to prevent cuts, be sure to wear gloves when handling the guide bar and saw chain.

・

Maintain the tension of the saw chain properly at all times.

・

If not enough tension is applied to the saw chain it can easily be dislodged when the saw chain

is in motion.

・

If too much tension is applied to the guide bar, saw chain and clutch may wear prematurely as

a result.

Cutting facing front

Guide bar

Circular hole on guide bar

Groove of guide bar

Sprocket

Adjuster

Regulating

screw

Chain cover

Nut

Saw chain

Nut

Lifts up 3 to 4 mm when

lifted lightly by fingers

Lifts up leading edge of guide bar

Saw chain lightly touches the guide bar

Regulating screw

Loosen

Tighten

Содержание TPS261

























Результаты поиска

Содержание TPS261

Отзывы:

Похожие инструкции для TPS261

Бренды по названию

Популярные бренды

Bushranger TPS261, Руководство владельца/оператора

Результаты поиска

Содержание TPS261

Отзывы:

Похожие инструкции для TPS261

Бренды по названию

Популярные бренды