manualshive.com logo in svg

Bushranger TPS261, Руководство владельца/оператора

Поделиться
Скачать
Bushranger TPS261 Скачать руководство пользователя страница 15

＿

 14 

＿

Working position

1. Choose a working position where the inclination of the 

pole remains at 60 degrees or less.

2.  Start  cutting  from  the  lower  branches  first  so  that  the 

branches will fall off easily when cut.

3. The cut branches may fall towards the worker, so be sure 

to select a location that enables a stable footing and 

provides an easy escape in the case of an emergency.

Adjusting length of shaft assembly

1. First of all, stop the engine then set the guide bar cover.
2. Loosen the clamping knob before adjusting the length of 

the shaft assembly. Be care falling down the clamping 

knob by over loosing.

3. Pull out or depress the shaft assembly from the slide 

holder for adjusting the shaft assembly length.

4. After adjusting the length, tighten the clamping knob firmly.

 WARNING

・ 

Wear a hat or helmet, protective glasses, gloves and 

ear plugs while working.

Furthermore, wear a dust mask whenever a lot of pol-

len or chipping powder is expected, which may be 

harmful for the health.

 CAUTION

・ 

Read the Safety instructions beginning on page 3 concerning proper use of the Pruner.

 WARNING

・ 

Always stop the engine and set the guide bar cover 

when adjusting the length of the shaft assembly.

60°

Operation

 DANGER

・  

Do not stand immediately below the branch that is to be cut. The branch may fall directly below 

and the branch may also bounce off other branches or the ground in an unexpected direction 

and cause injury to the worker.

・ 

Do not allow anyone to enter within a 15 meter radius.

・  

The Pruner is not insulated to prevent electric shock. Keep it away from any power lines with at 

least 15 meters when working, as there is threat of electrocution.

Guide Bar Cover

Slide Holder

Clamping Knob

Tighten

Loosen

Shaft Assembly

Содержание TPS261

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды