Bushranger TPS261 Скачать руководство пользователя

Страница: 10 / 24

＿

Before Operation

Chain Oil

1) Adding oil

1. Remove the oil tank cap and pour the chain oil (SAE

#10W-30) into the oil tank.

2. Once the oil has been poured into the oil tank, tighten the

oil tank cap to securely close the tank.

Oil tank cap

Oil tank

DANGER

・

Ensure that the guide bar and saw chain are installed on the pruner before verifying the

discharging rate of the chain oil. The rotator will be exposed and therefore dangerous if the

guide bar and the saw chain are not installed on the pruner.

CAUTION

・

It may take some time before the oil begins to discharge once the oil has been added to a new

product or when oil has been added to an empty tank. Do not turn the pruner on at a high speed in

such circumstances.

・

When a new chain is to be used, immerse the chain in chain oil for some time prior to installing

it on the pruner, or pour the oil directly on to the chain and the guide bar, after installing it on the

pruner. If they are not properly lubricated with oil the pruner may seize.

2) Regulating oil discharging rate

The regulating screw has three positions, Minimum, Interme-

diate and Maximum, only.
The regulating screw is set to Intermediate at the time of ship-

ping. It is recommended that the product be used with this

setting for ordinary use.

• Increase the discharging rate when cutting hard

branches or branches with a lot of resin (pitch), or

when the viscosity of the oil is high during winter.

1. Insert a minus screw driver into the regulating screw at the

bottom of the main unit.

2. When applying pressure with the minus screw driver, turn

the screw to the right (clockwise) to reduce the discharg-

ing rate and to the left (counter-clockwise) to increase the

discharging rate.

3. Turn the engine on and turn the saw chain, with the guide

bar facing the ground or tree. Oil will attach to the ground

or tree, if the oil is discharging.

WARNING

・

Using the pruner with a saw chain too loose may result in the saw chain becoming dislodged

and could cause an accident. Please be sure to check the tension of the saw chain before

starting any work.

Regulating screw

Minimum

Intermediate

Maximum

Be sure to turn the screw while applying

pressure to it with the screwdriver.

Содержание TPS261

























Результаты поиска

Содержание TPS261

Отзывы:

Похожие инструкции для TPS261

Бренды по названию

Популярные бренды

Bushranger TPS261, Руководство владельца/оператора

Результаты поиска

Содержание TPS261

Отзывы:

Похожие инструкции для TPS261

Бренды по названию

Популярные бренды