Burkert 8756 BATCH Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 52

Burkert 8756 BATCH Скачать руководство пользователя страница 9

Type 8756 BATCH

Safety instructions

9

WARNING!

Risk of injury that is due to escape of the fluid.

Contact with the operating fluid, its reaction products and vapours can cause injuries.

Inhaled vapours can be harmful.

▶

Observe all applicable accident protection and all applicable safety regulations relating to the operating
fluid used.

To avoid personal injury, obey the following instructions:

Only operate the product with a filtered fluid.

Make sure that the operating pressure of the product is not higher than the maximum authorized oper-
ating pressure. Refer to the data sheet of the product on our homepage:

country.burkert.com

.

Only use the product for fluids that are compatible with the product materials.

Do not make any modifications to the product and do not subject the product to mechanical stress.

Protect the installation and the product from accidental actuation.

Only trained personnel may perform the installation work and the maintenance work.

After an interruption in the electrical supply or in the fluid supply, ensure a controlled restart of the pro-
cess.

Observe best industry practice.

ATTENTION!

Components or assemblies at risk from electrostatic charges.

The product contains electronic components which are subject to electrostatic discharge (ESD). Contact
with electrostatically charged persons or objects endangers these components. In the worst case, they
could be defective immediately or might fail when energised.

▶

To minimise or even avoid any damage caused by an electrostatic discharge, take all the precautions
described in the EN 61340-5-1.

▶

Do not touch any of the live electrical components.

«
...
7
8
9
10
11
...
»

Содержание 8756 BATCH





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды