manualshive.com logo in svg

Burkert 8756 BATCH, Руководство по эксплуатации

Поделиться
Скачать
Burkert 8756 BATCH Скачать руководство пользователя страница 37

Type 8756 BATCH

Setting and operation

37

8.3.5

Configure the controller

Connect the product to the Bürkert Communicator software. Refer to chapter: 

Connect the product to

the Bürkert Communicator software [

}

 37]

In the Bürkert Communicator software, select the product.

Go to 

Controller

 > 

Parameter

 > Choose 

Start-Up Wizard

The product status indicator is orange.

A check-function event is generated.

Follow the instructions of the displayed wizard.

The connected actuator is configured.

The product operates normally.

8.4

Tools for doing the settings

The MassFlowCommunicator is another PC software that is not compatible with the product. You
cannot use the MassFlowCommunicator software to configure or operate the product.

Settings can be made with the Type 8920 Bürkert Communicator software.

To connect the product to the Bürkert Communicator software, refer to chapter: 

Connect the product

to the Bürkert Communicator software [

}

 37]

For general information about the Bürkert Communicator software, refer to the Type 8920 Operating In-
structions.

8.5

Connect the product to the Bürkert Communicator
software

8.5.1

Product variant büS /CANopen

To do the settings with the Type 8920 Bürkert Communicator software, do the following steps:

Buy the USB-büS-interface set with article number 00772426 from Bürkert. Refer to following figure.

büS stick with termination-
resistance switch

Fig. 13: USB-büS-interface set with article number 00772426

Download the latest version of the Type 8920 Bürkert Communicator software from

country.burkert.com

During installation, the büS stick must not be inserted at the PC. Install the Bürkert Communicator soft-
ware on a PC. Obey the installation recommendations given in the USBbüS- interface set.

The following figure shows the electrical connection parts that are used from the USB-büS-interface set.

Содержание 8756 BATCH





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды