Page 28
ENABLE ADS?
This function allows the operator to choose whether
or not to display the advertising message that was
entered into the brewer with an
AD CARD
. This mes-
sage will be displayed when the brewer is not in use.
Procedure to Enable/Disable Ads
:
1. Press and hold the ® pad until the display reads
SET NEW RECIPES
. Release the ®. Press and
release the ® until the display reads
ENABLE ADS
.
The
YES
or
NO
will be flashing to indicate the
current selection.
2. Press and release the
NO
pad to disable this
function (no ads will be displayed on the screen),
or;
3. Press and release the
YES
pad to enable this
function (ads will be displayed on screen).
4. When finished, press and release
DONE
to save the
new setting, exit the
ENABLE ADS
function and
advance to the next function screen,
SET TEMP.
Another alternative is to press and release either of
the
pads located on the front switch panel to
exit the
ENABLE ADS
function and return to the
MAIN SCREEN.
P2301
PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)
P2302
Procedure to set brew temperature:
1. Press and hold the ® pad until the display reads
SET NEW RECIPES
. Release button. Press and
release the ® until the display reads
SET TEMP
.
2. To adjust the brew temperature, press
(-)
to de-
crease or
(+)
to increase the brew temperature.
3. When finished, press and release
DONE
to save the
new setting, exit the
SET TEMP
function and
advance to the next function screen,
SET READY.
Another alternative is to press and release either of
the
pads located on the front switch panel to
exit the
SET TEMP
function and return to the
MAIN
SCREEN.
SET READY - Range: 185˚F (85˚C) to 203˚F (95˚C)
This function allows the operator to set the mini-
mum temperature allowable to start a brew cycle. The
range can be from 185˚F (85˚C) to within 2˚F of the
SET
TEMP.
The water must be at the
SET READY
tempera-
ture or higher for the display to indicate
READY TO
BREW
. If brew lockout is enabled, the brewing process
will not start below this
READY
temperature.
NOTE:
The upper limit is the water temperature control
setting minus 2˚F.
P2303
Procedure to set ready temperature:
1. Press and hold the ® pad until the display reads
SET NEW RECIPES
. Release the ® pad. Press and
release the ® pad until the display reads
SET
READY
.
2. To adjust the ready temperature, press the
(-)
button to decrease, or
(+)
to increase the ready
temperature.
3. When finished, press and release
DONE
to save the
new setting, exit the
SET READY
function and
advance to the next function screen,
REFILL.
35058 042105
SET TEMP - Range: 185˚F (85˚C) to 205˚F (96˚C)
This function allows the operator to set the brew
water temperature in the tank. It also sets the hot water
faucet dispense temperature.
Содержание Single TF DBC
