Bunn ICB SH, Руководство по программированию, Страница: 18 / 36

18
ENABLE ADS
This function allows the operator to choose whether
or not to display an advertising message. An ad can be
saved to the brewer by either writing the ad using the
programming commands, or by entering the ad into
the brewer using an
AD CARD
. This message will be
displayed when the brewer is not in use.
Procedure to Enable/Disable Ads:
1. Press and hold the right hidden button until the
display reads
RECIPES.
Press the right hidden
button until the display reads
SETTINGS
, then press
SELECT
. Press the right hidden button until the
display reads
ENABLE ADS
. The
YES
or
NO
will be
flashing to indicate the current selection.
2. Select
NO
to disable this function, or:
3. Select
YES
to enable this function.
4. When finished, select
DONE
to save the new setting
and advance to the next function screen.
5. If NO was selected, the display should now read
ENABLE SANITATION
. To exit programming and
return to the
MAIN SCREEN
, press
ENABLE BREW
ON/OFF
switch.
6. If
YES
was selected, the display should now read
NEW AD? . This screen allows the operator to select
between using an ad card to read in a new ad, or
writing an ad through the control panel.
Procedure to WRITE an Ad:
NOTE:
Writing and saving a new ad will erase any
previously saved ad in the brewer’s memory.
7. From the
NEW AD?
screen, select
WRITE
.
8. The display should now read
2 LINES 16 CHARS
AVAILABLE
, and then
SCROL THRU ALPHA, NEXT
-> NEXT LETTER,
and then
WRITE TOP LINE?
. The
ad can be up to 32 characters long, 16 per line. The
ad will be written in two steps, first the top line,
then the bottom line.
9. To write the top line of a new ad, select
YES.
To skip
the top line and only write a bottom line, select
NO
and proceed to step 13.
10. The display will now read
A
with a flashing cursor
below it. Press the
SCROLL
button to scroll through
the alphabet and available characters. When the
desired character is shown on the display, select
NEXT to move to the next character in the top line.
PROGRAMMING FUNCTIONS (cont.)
SET TEMP -
ICB SH/ICB TWIN SH
This function allows the operator to adjust the brew
water temperature in the tank. This also sets the hot
water faucet dispense temperature.
Procedure for setting the Set Temp
Range: 185° to 205° F (85° - 96° C)
1. Press and hold the right hidden button until the
display reads
RECIPES.
Press the right hidden
button until the display reads
SETTINGS
, then
press
SELECT
. Press the right hidden button until
the display reads
SET TEMP
.
2. Using (-) and (+) , adjust the brew and faucet
temperature.
3. When finished, press and release
DONE
to save
the new setting and to advance to the next function
screen,
READY DEGREE
. Press
ENABLE BREW ON/
OFF switch to exit programming and return to the
MAIN SCREEN
.
READY DEGREE
This function allows the operator to set the minimum
temperature allowable to start a brew cycle. The range
can be from 2° to 20° F below the set temperature. The
water must be at the
READY
temperature or higher
for the display to indicate
READY TO BREW
. If brew
lockout is enabled, the brewing process will not start
below this READY temperature.
Procedure to set ready temperature
Range: 2° to 20° F (2° to 10° C) below set temp
1. Press and hold the right hidden button until the
display reads
RECIPES.
Press the right hidden
button until the display reads
SETTINGS
, then
press
SELECT
. Press the right hidden button until
the display reads
READY DEGREE
.
2. Using (-) and (+) , adjust the ready temperature.
3. When finished, select
DONE
to save the new setting
and to advance to the next screen,
ENABLE ADS
.
Press
ENABLE BREW ON/OFF
switch to exit.
PROGRAMMING BREWER
(cont.)
(cont.)