13
20. When finished setting both batch sizes, press
DONE
. The display will show the pulse settings to
accommodate the brew time entered. Press and
release each batch size to display the settings for
that batch. After a delay, the display should read
3
BATCHES DONE?
21. If both batch sizes are not correct, press
NO
to
return to the
BREW TIME
setup screen and repeat
steps 18-20.
Setting Pulse Brew/PreInfusion – MANUAL
22. Select
MANUAL.
With
MANUAL
flashing, select
NEXT
.
23. The display should now read,
1
st
ON TIME
and a
batch light will be blinking. Select the batch size to
be modified.
24. Using
(-)
or
(+)
, adjust the
1
ST
ON TIME
.
25. When finished, press the other batch size and repeat
step #24.
NOTE:
To disable pulse brew, set
1
ST
ON TIME
to OFF.
Brewer will automatically pulse on tea recipes with a
brew volume greater than 86.0 oz.
26. When finished setting both batch sizes, press
DONE
.
27. The display should now read
OFF TIME.
Adjust the
OFF TIME
using
(-)
or
(+)
.
28. When finished, press the other batch size and repeat
step # 27.
29. When finished setting both batch sizes, press and
release
DONE
.
30. The display should now read
LAST ON:
. Adjust the
LAST ON TIME
using
(-)
or
(+)
. If
PREINFUSION
is desired, set the
LAST ON TIME
to
PreI
.
31. When finished, press the other batch size and repeat
step # 30.
32. When finished setting both batch sizes, press and
release
DONE
.
33. The display will show the three times just entered.
Press and release each batch size to display the set-
tings for that batch. If the
1
ST
ON TIME
is set to
OFF
,
the display will read
PULSE BREW DISABLED
. After
a 5 second delay, the display will read
3 BATCHES
DONE?
INITIAL SPRAY
INITIAL SPRAY
ALTERNATES UNTIL
BREW CYCLE IS
COMPLETED
PRE-INFUSION
REMAINING ON
ON-
TIME
OFF-
TIME
OFF-TIME
OFF-
TIME
OFF-
TIME
ON-
TIME
ON-
TIME
9. If both batch sizes are correct, press
YES
. This will
advance to the
BYPASS %
10. Using (-) or (+), set the amount of bypass water for
that particular batch size to be dispensed around
the filter/grounds.
11. When finished, press the other batch size and repeat
step #10.
12. When finished setting both batch sizes, press and
release
DONE
. The display should read
3 BATCHES
DONE?
13. If all batch sizes are not correct, select
NO
to return
to the
BYPASS %
function and repeat steps #10-12.
14. If both batch sizes are correct, press
YES
. This will
advance to the
SET PULSE BREW
.
15. To set
PULSE BREW
press
YES
. The display
should now read
SELECT METHOD
. To set the
EASY
method, continue to step #16. To set by
MANUAL
method, jump to step #21.
Setting Pulse Brew – EASY Pulse Brew
Range: Minimum: will adjust to the minimum time
required to brew that batch using the set brew volumes
and flow rate for the sprayhead. Maximum – will adjust
depending on settings and will always be minimum time
+ 3 minutes. The brewer will automatically calculate what
the
1ST ON TIME
,
OFF TIMES
, and
LAST ON TIME
will
be using
THE INITIAL ON TIME
, plus a 7 pulse routine.
16. Select
EASY
. With
EASY
flashing, select
NEXT
.
17. The display should now read
BREW TIME:
and a
batch light will be blinking. Select the batch size to
be modified.
18. Using
(-)
or
(+)
, set the total brew time desired
including spray times and off times.
19. When finished, press the other batch size and repeat
step #18.
PROGRAMMING BREWER
(cont.)
PROGRAMMING FUNCTIONS
(cont.)
(cont.)
