Bungard FilmStar-PLUS Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 16

background image

Photoplotter FilmStar-PLUS
Instructions to Use

Page 3 / 16

Inside the Plotters are no user-serviceable parts. The case may be opened only by experts.
Connect only to the specified voltage and current.
During plotting, the film is exposed by a laser beam. This can damage the human eye. Do not look into
the laser beam during operation!
Temperature and humidity affect the accuracy of the plotter. Avoid variations in temperature and hu-
midity. Environment should be clean and dust-free and by no means corrosive!
The photo films are very light-sensitive. Protect them till the end of the fixing process from light!
Store film and chemicals in a cool, dark and dry place.
Before you use the film, let it acclimatize 24 hours at min. to the processing temperature.
When handling chemicals wear personal protective equipment (gowns, gloves, goggles).
The drum surface should be kept clean and dry. To remove any remnants of the tape, use a soft cloth
moistened with a liquid detergent. Do not use a spray.
The fixer contains silver and must be recycled! Safety data sheets for the developer and fixer concen -
trates are available. These are actually no dangerous goods according to transport regulations.

Amount of Delivery:

1 Plotter
1 Software CD
3 Testfilms

(1 x lightbar for light calibration, 1 x test grid film for dimensional calibration, 1 x test film

with plot samples

1 power supply

Accessories

Dark Room for Filmstar-PLUS,

Fixing Pins

Dark Room lamp assembly green
60 cm complete

Developer and Fixer

Film-Punch

Triple Tank for Filmstar

Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany

Tel.: +49 2292 / 9 28 28-0, Fax: +49 2292 / 9 28 28-29

, E-mail: [email protected]

«
1
2
3
4
5
...
»

Содержание FilmStar-PLUS

















Отзывы:

Нет отзывов

Похожие инструкции для FilmStar-PLUS

Бренд: Furuno Страницы: 201

MICROPLOTTER II

Бренд: SONOPLOT Страницы: 67

Бренд: Roland Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды