Bungard FilmStar-PLUS Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

background image

Photoplotter FilmStar-PLUS
Instructions to Use

Page 2 / 16

Technical Data

Maximum plot size:

365 x 375 mm (L x B)

Maximum film format:

405 x 395 mm (L x B)

Maximum file size:

256 MB

Speed:

7 mm of film width / min. at 2032 dpi

Light source:

Laser-diode 670 nm (red)

Data formats:

Gerber, Extended Gerber, Hi-Res BMP

Extent of delivery:

Photoplotter and Software on CD

System requirements:

Windows XP / Windows 7 / Windows 8

Dimensions:

710 x 340 x 200 mm (L x W x H)

Weight:

Approx. 25 kg

Power supply

External power supply Input 100V-240V /
47–63 Hz; Output 36V- DC

Technical resolution:

Resolution X:

1625, 2032, 3251, 4064, 6502, 8128,
16256

Resolution Y:

25 400dpi

Graphical resolution:

1) Finest point/ Finest line = 5 µm (0.005 mm/0.19685 mil).

2) Finest space between 2 lines = 10 µm (0.01 mm/0.3937 mil)

3) Finest space between 2 areas = 18 µm (0.018 mm/0.70866 mil)

4) Finest inverse spot diameter (transparent point in black area) = 25 µm
(0.025 mm/0.98425 mil)

Safety Regulations:

Carefully read this instructions and especially the safety regulations before using the unit. Also pay
heed to the safety data sheets of the photographic chemicals. Keep these instructions in a safe place
in case you need to refer to them in the future.
The photoplotter Filmstar Plus is designed for use in the laboratory and may be operated only by
trained professionals.
Apply the general safety regulations for the operation of electrical equipment.
Before any maintenance work disconnect plotter from mains voltage.

Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany

Tel.: +49 2292 / 9 28 28-0, Fax: +49 2292 / 9 28 28-29

, E-mail: [email protected]

«
1
2
3
4
...
»

Содержание FilmStar-PLUS

















Отзывы:

Нет отзывов

Похожие инструкции для FilmStar-PLUS

Бренд: Roland Страницы: 144

Бренд: Partex Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды