BTR DG-Mini страница 61 Скачать руководство пользователя

Страница: 61 / 71

BTR Controls, Inc

TROUBLESHOOTING

DG-Mini V7 Rev. C Standard HW manual V 1.0.2

Table of Error Codes

Error
Code:

Description

Level

Cause:

Check:

OC2

Overcurrent

Medium Priority

The motor current has
exceeded the inverter
rating by 150% for more
than 30 seconds.

Check for mechanical
obstructions.

OC3

Overcurrent

Medium Priority

Over current while
accelerating, the
acceleration is too fast.

Check that the door is not
binding, may need to reduce
the acceleration level using the
menu

System

Config

Ramps

ACC OPEN

OC4

Overcurrent

Medium Priority

Over current while dc
braking operates.

The dc braking is too
aggressive, adjust the DC Break
level and duration using the
menu

Sys Config

Motor

Config

DC Brake

OC5

Overcurrent Peak

High Priority

Severe overload, possibly
permanent damage to
the controller.

Check for a short. Check that
the motor is not stalled. Check
that the brake is releasing. May
need to decrease the boost
level using the menu

Sys

Config

Motor Config

Boost

Controller

Overheated

Fault Specific

Overheating inside the
panel, the inverter is too
hot.

Check ventilation. Check that
current limits have not been
exceeded.

12V Supply Shorted

Fault Specific

24V Supply Shorted

Fault Specific

Low internal 12V or 24V
supply.

Check I/O wiring for short or
overload.

E01

Mechanical Overload

Low Priority

Mechanical overload
(slip monitoring) or
missing signal from the
encoder.

Check the encoder wiring.
Check that the motor is not
stalled. Check for possible
mechanical obstruction.

E02

Direction Error

Low Priority

Direction error.

Check encoder wiring. Rerun a
Quick Setup.
Confirm that the pulses count
up while opening and down
when closing the door.

E03

No Encoder Signal

Low Priority

No signal from the
encoder - (only during
installation).

Check the wiring related to the
encoder, and any possible
mechanical obstruction.

E04

Speed Error

Low Priority

Speed error

Check the wiring related to the
encoder, check gear ratio.

E05

Ref. Connection Error

Medium Priority

The reference switch is
shorted or broken.

Check the reference switch.

E06

Ref. Switch Position

Error

Medium Priority

The reference switch
operates in the wrong
position.

If using an incremental encoder
the reference switch has
activated at the wrong position,

Содержание DG-Mini








































































Результаты поиска

Содержание DG-Mini

Отзывы:

Похожие инструкции для DG-Mini

Бренды по названию

Популярные бренды

BTR DG-Mini, Руководство пользователя

Результаты поиска

Содержание DG-Mini

Отзывы:

Похожие инструкции для DG-Mini

Бренды по названию

Популярные бренды