BTR DG-Mini Скачать руководство пользователя страница 30

Страница: 30 / 71

BTR Controls, Inc.

PROGRAMMING

DG-Mini V7 Rev. C Standard HW manual V 1.0.2

Main Menu

The main menu is entered by pressing the MENU/ENTER button from the

Idle

menu

AIN MENU

Menu Name

Description:

System Status

A read-only menu that provides status displays for use in setup and
troubleshooting.

Profile Selection

A menu used during installation to load the default settings for a specific
door type.

CAUTION

Loading a profile will cause
all related parameters to
be overwritten with the
defaults of the loaded
profile!

Limit Setup

A menu to setup or adjust the door positions.

System Config

A menu to configure the controller’s settings.

YSTEM STATUS

Description:

Overview

Displays the controller’s serial number, ratings and software revision.

Photoeyes

Displays the status of the photoeyes.
Change between photoeye 2 by pressing the

button

Position

Displays the current encoder count.
If an incremental encoder is used information about the reference status
is also shown here. This screen may also display the status of the
encoder’s internal battery when supported.

Содержание DG-Mini








































































Результаты поиска

Содержание DG-Mini

Отзывы:

BTR DG-Mini, Руководство пользователя, Страница: 30 / 71

Результаты поиска

Содержание DG-Mini

Отзывы: