BTR DG-Mini Скачать руководство пользователя страница 57

Страница: 57 / 71

BTR Controls, Inc.

PROGRAMMING

DG-Mini V7 Rev. C Standard HW manual V 1.0.2

YSTEM

This menu is used for system-wide and factory configuration.

Description:

Clear Fault Log

This submenu is used to clear the fault log. The

button must be

pressed to confirm the action.

Clear Service

This submenu is used to clear service messages.
The

button must be pressed to confirm the action.

Clear Cycle Cnt

Factory use only.

Sound

This submenu is used to enable or disable the internal sounder.

Backlight

This submenu is used to enable or disable the display’s backlight.

Contrast

This submenu is used to set the display’s contrast.

SW Update

This submenu is used for updating the DG-Mini firmware.

System Info

This submenu is used to identify the DG-Mini and includes Type,
Power Size , and Voltage Rating.

SW Info

This submenu displays the DG-Mini’s current software version.

Factory

Factory use only.

Language

This submenu is not supported at this time.

Diagnostics

Factory use only.

Содержание DG-Mini








































































Результаты поиска

Содержание DG-Mini

Отзывы:

Бренды по названию

Популярные бренды

BTR DG-Mini, Руководство пользователя

Результаты поиска

Содержание DG-Mini

Отзывы:

Бренды по названию

Популярные бренды