BTR DG-Mini Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 71

BTR DG-Mini Скачать руководство пользователя страница 54

BTR Controls, Inc.

PROGRAMMING

DG-Mini V7 Rev. C Standard HW manual V 1.0.2

54

S

EY

W

AVE

The DG-Mini has the ability to interface with optional BTR peripherals such as the Seywave® Wireless System and the
wireless Illumadoor® LED Signaling System. This menu is used to configure any of these supported options.

The Seywave Wireless System allows for quick, reliable and cost-effective connection of peripherals such as
pushbuttons, pull-cords, and palm operators for remote activation without the expense of running conduit. Additionally,
the Seywave Wireless System supports a Sensor module that meets UL 325 Standards for Entrapment Protection.

The Illumadoor® is an LED strip light that can be used to provide visible indication of status for industrial doors . Each
strip has 30 individual Red, Amber and Green LED’s that can be wirelessly controlled from the DG-Mini when using the
BTR Illumadoor® combination power supply and junction box. The DG-Mini controller has predefined and selectable
logic covering a vast array of signaling applications from simple door position to air lock traffic control.

S

EY

W

AVE

Description:

Seywave Host

This submenu is used to configure the Internal SeyWave host.

Illumadoor

This submenu is used to configure the optional Illumadoor®
peripheral.

«
...
52
53
54
55
56
...
»

Содержание DG-Mini








































































Отзывы:

Нет отзывов