BT Redcare Secure Mk3 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 44

background image

July 2013 © British Telecommunications plc 2013

Page 40

Disposal

The symbol shown here and on the product, means that the product is
classed as Electrical or Electronic Equipment and should not be disposed
of with other household or commercial waste at the end of its working life.

The Waste Electrical and Electronic Equipment (WEEE) Directive
(2002/96/EC) has been put in place to recycle products using the best
available recovery and recycling techniques to minimise the impact on the
environment, treat any hazardous substances and avoid the increasing
landfill.

Product disposal instructions for users:

Please dispose of the product as per your local authority’s recycling processes. For more
information please contact your local authority or retailer where the product was purchased.

The product may be returned to the Freepost address below:

BT SUPPLY CHAIN
DARLINGTON ROAD ,
NORTHALLERTON.
NORTH YORKSHIRE
DL6 2PJ

.

Republic of Ireland customers can return the product to any of the following addresses:

BT IRELAND
27 WILLSBOROUGH INDUSTRIAL
ESTATE
CLONSHAUGH
DUBLIN 17

BT IRELAND
GRAND CANAL PLAZA
GRAND CANAL DOCK
DUBLIN 2

BT IRELAND
DUNDRUM BUSINESS PARK
DUNDRUM
DUBLIN 14

Disclaimer

The manufacturer or his agents disclaim responsibility for any damage, financial loss or injury
caused to any equipment, property or persons resulting from any use of this equipment. The
manufacturer is not liable for any purely economic loss arising from any use of this equipment.
All responsibility and liability in the use of BT Redcare products are assumed by the user.

This unit is designed to be used in customer premises. Use of this equipment in other
locations may void warranty. This unit is not intended for use in marine environments or water
borne vessels.

BT Redcare may make changes to features and specifications at any time without prior
notification in the interest of ongoing product development and improvement.

«
...
40
41
42
43
44
»

Содержание Redcare Secure Mk3













































Отзывы:

Нет отзывов

Похожие инструкции для Redcare Secure Mk3

Бренд: Harman Kardon Страницы: 2

Бренд: Wayne Страницы: 16

Бренд: Ultrasonic Страницы: 16

Бренд: 3M Страницы: 88

Aqua-Pure AP510

Бренд: 3M Страницы: 16

Бренд: Ecco Страницы: 2

Бренд: Wavetronix Страницы: 4

Бренд: wavestore Страницы: 11

Бренд: X-10 Страницы: 32

Бренд: YORKVILLE Страницы: 79

PLASMA CUTTING Series

Бренд: Vector Welding Страницы: 56

Бренд: RTRMAX Страницы: 14

X Wireless Series

Бренд: Axess Страницы: 8

Бренд: Digimerge Страницы: 44

Бренд: Grundig Страницы: 40

Бренд: Velleman Страницы: 22

Бренд: HK Audio Страницы: 20

IPC-HFW1230S1-0280B-S5

Бренд: Dahua Technology Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды