background image

V.

INSTALL BAROMETRIC BYPASS DAMPER

NOTE:

The barometric bypass damper is a critical part of Zone

Perfect Plus System for controlling noise at minimum airflow. A
barometric bypass should be installed unless the duct work and
indoor unit have been sized for use without a bypass.

The bypass should be installed according to local codes and
SMACNA standards. Be sure bypass is properly supported.

For proper installation, refer to Installation Instructions packaged
with barometric bypass.

CAUTION:

Failure to properly install leaving air tem-

perature sensor can cause permanent damage to the
HVAC equipment.

VI.

INSTALL LEAVING AIR TEMPERATURE (LAT)

SENSOR

Locate LAT sensor in main supply trunk after heating and cooling
coil and before bypass damper and first branch. The LAT sensor is
radiant shielded to prevent heat from affecting correct air tempera-
ture.

1. Drill a 1/4-in. hole at location in supply trunk where sensor

will be installed.

2. Insert sensor in hole and use as a template to mark the 2

mounting holes.

3. Drill two 1/16-in. holes to accept No. 6 screws through

pre-drilled holes in duct temperature sensor back plate.

4. Use 2 No. 6 sheet metal screws to mount duct temperature

sensor to unit.

5. Connect sensor to 2-conductor wire using provided wire

nuts. (See Fig. 9, 10, or 11 for connection to Equipment
Controller.)

VII.

INSTALL HEAT PUMP TEMPERATURE (HPT)

SENSOR

The HPT sensor is required in all heat pump/fan coil installations.
It is not used in dual fuel(heat pump/furnace installation). It
measures the temperature of the air leaving the indoor coil. The
sensor is to be installed downstream of the indoor coil but before
the electric heaters. It can be installed through the wall of the fan
coil or may be located entirely inside the fan coil near the blower
inlet. Anchor firmly in place with cable ties so that it cannot
interfere with the blower wheel. (See Fig. 9, 10, or 11 for
connection to Equipment Controller.)

VIII.

FINAL WIRING

Bring all Equipment Controller wires together at Equipment
Controller. Make all connections as indicated on Fig. 9 (for 2-zone
installations), Fig. 10 (for up to 4-zone installations), or Fig. 11
(for up to 8-zone installations).

Figures 15 through 38 show the connection between the Equip-
ment Controller and the HVAC equipment. Select proper diagram
for your equipment and connect accordingly. This connection will
require as few as 4 or as many as 7 conductors. See Table 4 to
identify the correct wiring figure.

NOTE:

Table 4 and wiring diagrams appear in sequence near the

end of this document.

NOTE:

It is good practice to mark each wire as the final

connection is made. This will preserve its identity if it is ever
disconnected.

Fig. 9—2-Zone System Wiring Diagram

A98085

O  REVERSING VALVE COOL
B  REVERSING VALVE HEAT
RH  HEATING TRANSFORMER
RC  COOLING TRANSFORMER

SEE

FIGURES FOR

EQUIPMENT

WIRING

DEFROST

JUMPER NEEDED

FOR HEAT PUMP

APPLICATIONS

24 VAC

ZONING

TRANSFORMER

C
RZ

DHUM  DEHUMIDIFY

DEF  DEFROST 

HUM  HUMIDIFY

G  FAN
W2 HEAT STAGE 2
W1 HEAT STAGE 1
Y2 COMPRESSOR STAGE 2
Y1 COMPRESSOR STAGE 1

HPT

HPTC

LAT

LATC

OATC

OAT

OUTDOOR AIR
TEMP SENSOR
LEAVING AIR
TEMP SENSOR
HEAT PUMP
TEMP SENSOR

CLS1
COM1
OPN1
CLS2

DAMPERS

OPTION
SWITCHES
NOTE SWITCH
#8 IS AT TOP

CLS_
COM_
OPN_

8

1

=
=
=

CLOSE
COMMON = 24VAC FROM RZ
OPEN

COM2
OPN2

ZONE 1

DAMPER

ZONE 2

DAMPER

DAMPER

FUSE

3A

D20

(LED)

2 ZONE EQUIPMENT CONTROLLER

NOTES:   

*

 = OPTIONAL COMPONENTS

                   = INSTALLING ZONE 1 REMOTE SENSOR AT OS1 AND OS1C WILL OVERRIDE 

      TEMPERATURE SENSOR ON USER INTERFACE
   = COMMUNICATION BUS ARE IN PARALLEL WITH EACH OTHER
      (EITHER CONNECTOR CAN BE USED)

V+

USER INTERFACE

RS+

V+

RS+

RS-

VG

V+

RS+

RS-

VG

OS1

OS1C

ZS2

ZS2C

RS-
VG

VG

OPTIONAL 
ZONE 1
SENSOR

REMOTE

SENSORS

ZONE 2
SENSOR

COMMUNICATION

BUS

COMMUNICATION

BUS

V+

SMART SENSORS*

RS+
RS-

WHITE

RED

BLUE/YELLOW

GREEN

WHITE

RED

BLUE/YELLOW

GREEN

—5—

Содержание ZONE PERFECT PLUS ZONEBB2KIT





























Отзывы: