background image

B.

Rectangular Metal Duct Work

1. Make connections using S-lock and drives. (See Fig. 3.)

2. Properly seal joint using duct tape, mastic, or other ap-

proved method. Do not allow mastic to come in contact
with actuator.

3. Insulate damper using 1-1/2 in. to 2-in. insulation. (Check

your local codes.) (See Fig. 4.)

NOTE:

All zone dampers and duct work must be properly

supported according to local codes or SMACNA standards.

C.

Round Flexible Duct Work

1. Slip 1 end of flexible duct work over 1 end of zone damper.

(See Fig. 5.)

2. Secure flexible duct to zone damper using SMACNA or

other approved method.

3. Properly seal joint using duct tape, mastic, or other ap-

proved method. Do not allow mastic to come in contact
with actuator.

4. Insulate damper using 1-1/2 in. to 2-in. insulation. (Check

your local codes.) (See Fig. 6.)

NOTE:

All zone dampers and duct work must be properly

supported according to local codes or SMACNA standards.

D.

Rectangular Fibrous Glass Duct Work

1. Insert 1 end of zone damper into 1 end of fibrous glass duct

work approximately 2 to 3 in. (See Fig. 7.)

2. Screw field-supplied screws and tabs into zone damper.

3. Properly seal joint using duct tape, mastic, or other ap-

proved method. Do not allow mastic to come in contact
with actuator.

4. Insulate damper using 1-1/2 in. to 2-in. insulation. (Check

your local codes.) (See Fig. 8.)

Fig. 2—Insulated Round Metal Duct Work

A95130

/  

 STEEL STRAP

1

2

Fig. 3—Rectangular Metal Duct Work

A92478

DRIVE

ZONE
DAMPER

S-LOCK

SUPPLY
AIR DUCT

Fig. 4—Insulated Rectangular Metal Duct Work

A95131

1  /  " TO 2"

INSULATION

1 2

Fig 5—Round Flexible Duct Work

A95132

FLEXIBLE

DUCT

ZONE

DAMPER

Fig. 6—Insulated Round Flexible Duct Work

A95133

/  

 STEEL STRAP

1 2

Fig. 7—Rectangular Fibrous Glass Duct Work

A92480

ZONE
DAMPER

2

 TO 3

FIBROUS
GLASS
DUCTWORK

FIELD
SUPPLIED
SCREWS

Fig. 8—Insulated Rectangular Fibrous Glass

Duct Work

A95134

1  /  

 TO 2

INSULATION

1 2

—4—

Содержание ZONE PERFECT PLUS ZONEBB2KIT





























Отзывы: