Bryant ZONE PERFECT PLUS ZONEBB2KIT Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

background image

→

SMART SENSOR OPERATION

NOTE:

Refer to Smart Sensor Installation and Start-Up Instructions for proper installation and set-up procedure.

The Smart Sensor can control the setting of zone temperature, OUT, HOLD, or OFF. It can also display outdoor temperature and indoor humidity.

A97187

A.

Changing Desired Temperature

1. The current temperature in that zone will be displayed in the LCD.

2. Press UP or DOWN button to display desired temperature for that zone. The LCD will display the

current mode of operation, either heat or cool.

3. Press UP or DOWN button again as needed until new desired temperature is shown.

4. Press SET TEMP button to change temperature between COOL desired temperature and HEAT

desired temperature.

5. Pressing HOLD button will hold desired temperature setting indefinitely. Pressing HOLD button

again removes HOLD function.

6. Pressing OUT button will program zone as being unoccupied. Pressing OUT button again changes

zone to occupied. When a zone is set to OUT, desired temperature will be displayed as dashes when
UP and DOWN buttons are pressed.

B.

Viewing Outdoor Temperature and Indoor Humidity

1. Pressing both UP and DOWN buttons simultaneously will display outdoor temperature, if this

feature is included, and indoor humidity. Outdoor temperature will be displayed first for 5 sec,
followed by humidity for 5 sec. Smart Sensor will then return to normal. The humidity value will
be humidity level as measured at user interface.

NOTE:

If All Zone feature has been enabled from user interface, you will not be able to override settings

at Smart Sensor location. The desired temperature will be displayed as dashes when UP and DOWN
buttons are pressed. You must first remove All Zone function by pressing ALL ZONE button on user
interface.

A Smart Sensor does not remove or transfer features from User Interface. It only provides a location within
zone where access is provided to some of User Interface features. Any input that can be provided at Smart
Sensor can also be provided at User Interface.

OUT

COOL

DESIRED TEMP

OUT

Smart Sensor display

with ALL ZONE enabled

—15—

«
...
13
14
15
16
17
...
»

Содержание ZONE PERFECT PLUS ZONEBB2KIT





























Отзывы:

Нет отзывов

Похожие инструкции для ZONE PERFECT PLUS ZONEBB2KIT

Бренд: MADRIX Страницы: 36

Бренд: Magnescale Страницы: 3

Бренд: Eaton Страницы: 8

Бренд: X Rocker Страницы: 38

Бренд: Savant Страницы: 2

Бренд: Vertiv Страницы: 2

Бренд: Quantum Страницы: 20

Бренд: Bentel Security Страницы: 4

Бренд: Whale Страницы: 8

Бренд: Tascam Страницы: 8

Бренд: Atari Страницы: 3

Бренд: Konig Страницы: 47

Бренд: Yoshitake Страницы: 21

Бренд: Oasis Страницы: 7

FLECK 5810 XTR2

Бренд: Pentair Страницы: 36

Бренд: Wenshing Страницы: 4

Бренд: CALEFFI Страницы: 10

EZ-ZONE PM L AAAAB Series

Бренд: Watlow Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды