background image

19

GUIDE SPECIFICATIONS

INDOOR WALL- MOUNTED DUCTLESS UNITS

Size Range: 3/4 to 2 1/2 Ton Nominal Cooling and Heating Capacity

Model Number: 619P

PART 1 - GENERAL

1.01 System Description

Indoor, wall- mounted, direct- expansion fan coils are matched with

the heat pump outdoor unit.

1.02 Agency Listings

Unit shall be rated per AHRI Standards 210/240 and listed in the

AHRI directory as a matched system.

1.03 Delivery, Storage, And Handling

Units shall be stored and handled per unit manufacturer’s

recommendations.

1.04 Warranty (For Inclusion By Specifying

Engineer)

PART 2 - PRODUCTS

2.01 Equipment

A. General:

Indoor, direct- expansion, wall- mounted fan coil. Unit shall be

complete with cooling/heating coil, fan, fan motor, piping

connectors, electrical controls, microprocessor control system, and

integral temperature sensing. Unit shall be furnished with integral

wall mounting bracket and mounting hardware.

B. Unit Cabinet:

Cabinet discharge and inlet grilles shall be attractively styled,

high- impact polystyrene. Cabinet shall be fully insulated for

improved thermal and acoustic performance.

C. Fans:

1. Fan shall be tangential direct- drive blower type with air

intake at the top of the unit and discharge at the bottom

front. Automatic, motor- driven vertical air sweep shall be
provided standard.

2. Air sweep operation shall be user selectable. The vertical

sweep may be adjusted (using the remote control) and the

horizontal air direction may be set manually.

D. Coil:

Coil shall be copper tube with aluminum fins and galvanized steel

tube sheets. Fins shall be bonded to the tubes by mechanical

expansion. A drip pan under the coil shall have a drain connection

for hose attachment to remove condensate. Condensate pan shall

have internal trap.

E. Motors:

Motors shall be open drip- proof, permanently lubricated ball

bearing with inherent overload protection. Fan motors shall be

4- speed.

F. Controls:

Controls shall consist of a microprocessor- based control system

which shall control space temperature, determine optimum fan

speed, and run self diagnostics. The temperature control range

shall be from 62

_

F to 86

_

F (17

_

C to 30

_

C) in increments of 1

_

F

or 1

_

C, and have 46

_

F Heating Mode (Heating Setback). The

wireless remote controller shall have the ability to act as the

temperature sensing location for room comfort.

The unit shall have the following functions as a minimum:

1. An automatic restart after power failure at the same

operating conditions as at failure.

2. A timer function to provide a minimum 24- hour timer

cycle for system Auto Start/Stop.

3. Temperature- sensing controls shall sense return air

temperature.

4. Indoor coil freeze protection.
5. Wireless infrared remote control to enter set points and

operating conditions.

6. Automatic air sweep control to provide on or off activation

of air sweep louvers.

7. Dehumidification mode shall provide increased latent

removal capability by modulating system operation and set

point temperature.

8. Fan- only operation to provide room air circulation when no

cooling is required.

9. Diagnostics shall provide continuous checks of unit

operation and warn of possible malfunctions. Error

messages shall be displayed at the unit.

10. Fan speed control shall be user- selectable: turbo, high,

medium, low, or microprocessor controlled automatic
operation during all operating modes.

11. Automatic heating- to- cooling changeover in heat pump

mode. Control shall include deadband to prevent rapid
mode cycling between heating and cooling.

12. Indoor coil high temperature protection shall be provided to

detect excessive indoor discharge temperature when unit is

in heat pump mode.

G. Filters:

Unit shall have filter track with factory- supplied cleanable filters.

H. Electrical Requirements:

Indoor fan motor to operate on 115V on model sizes 09- 12 and on

208- 230V on model sizes 09- 30, as specified. Power is supplied

from the outdoor unit.

I. Operating Characteristics:

The 619P system shall have a minimum SEER (Seasonal Energy

Efficiency Ratio) and HSPF at AHRI conditions, as listed on the

specifications table.

J. Refrigerant Lines:

All units should have refrigerant lines that can be oriented to

connect from the left, right or back of unit. Both refrigerant lines

need to be insulated.

K. Special Features (Field Installed):

1. Condensate Pump:

- The condensate pump shall remove condensate from the

drain pan when gravity drainage cannot be used. Pump
shall be designed for quiet operation. Pump shall consist of

two parts: an internal reservoir/sensor assembly, and a
remote sound- shielded pump assembly. A liquid level
sensor in the reservoir shall stop cooling operation if the

liquid level in the reservoir is unacceptable.

Содержание 538PR





















Отзывы: