Brute MagnaTech BMGH1600, Инструкция по установке и эксплуатации, Страница: 14 / 116

Page 10 B
RADFORD
W
HITE
WARNING
All venting must be installed according to this
manual and any other applicable local codes,
including but not limited to, ANSI Z223.1/NFPA 54,
CSA B149.1, CSAB149.2 and ULC S636. Failure
to follow this manual and applicable codes may
lead to property damage, severe injury, or death.
If the system temperatures are unknown at
the time of installation, class IIC or higher
venting material is recommended.
The MagnaTech is a Category IV appliance and
may be installed with the standards listed on
Table 6.
The unit’s vent can terminate through the roof,
or through an outside wall.
All installations must be done following the vent
supplier’s recommended installation techniques.
If these are not available, refer to the Bradford
White recommendations for the material used.
NOTE: For Category IV boilers, have
horizontal runs sloping upwards not less than
1/4 inch per foot (21 mm/m) from the boiler to
the vent terminal; be installed so as to prevent
accumulation of condensate; and, where
necessary, have means provided for drainage
of condensate.
ATTENTION: Pour la catégorie IV, les
chaudières ont horizontal en pente vers
le haut au moins 1/4 de pouce par pied
(21 mm/m) à partir de la chaudière pour
l’évent borne; être installé de façon à éviter
l’accumulation de condensats; et, le cas
échéant, ont des moyens prévus pour
l’évacuation des condensats.
This will allow the condensate to run back to
the MagnaTech to drain. Route the vent pipe
to the heater as directly as possible. Seal all
joints. Provide adequate hangers as required in
the venting system manufacturer’s Installation
Instructions, or at least every 4 feet.
The unit must not support the weight of the
vent pipe. The maximum equivalent pipe
length allowed is 100 feet (30m). Each elbow
Table 5. Vent Accessories
(Place in section 3.1)
Model 1600 Model 2000 Model 2500 Model 3000 Model 3500 Model 4000
Screen for horizontal galvanized air pipe D2012104 D2012101 D2012101 D2012102 D2012103 D2012103
Screen for horizontal PVC air pipe CA012004 CA012001 CA012001 CA012002 CA012003 CA012003
Screen for horizontal polypropylene air pipe CA012204 CA012201 CA012201 CA012202 CA012203 CA012203
Screen for vertical galvanized air pipe D2012204 D2012201 D2012201 D2012202 D2012203 D2012203
Screen for vertical PVC air pipe CA012404 CA012401 CA012401 CA012402 CA012403 CA012403
Screen for vertical polypropylene air pipe CA012604 CA012601 CA012601 CA012602 CA012603 CA012603
Table 3a - Ducted Air Accessories
(Place in section 3.2)
Model 1600 Model 2000 Model 2500 Model 3000 Model 3500 Model 4000
Horizontal vent terminal for stainless steel D2012004 D2012001 D2012001 D2012002 D2012003 D2012003
Screen for horizontal CPVC vent CA012104 CA012101 CA012101 CA012102 CA012103 CA012103
Screen for vertical stainless steel vent D2012304 D2012301 D2012301 D2012302 D2012303 D2012303
Screen for vertical CPVC vent CA012504 CA012501 CA012501 CA012502 CA012503 CA012503
Table 3* - Vent Accessories
(Place in section 3.5)
Model 1600 Model 2000 Model 2500 Model 3000 Model 3500 Model 4000
Air intake screen for unit placed outdoors CA0011904 CA011901 CA011901 CA011902 CA0011903 CA0011903
Vent terminal for unit placed outdoors CA011803 CA011801 CA011801 CA011802 CA011803 CA011803
Table 3** - Air & Vent Accessories for Units Placed Outdoors
Installation Standards
Material United States Canada
Stainless steel UL 1738 Venting must be ULC S636 certified for use as
venting material. The venting material class must
be chosen based upon the intended application
of the boiler, and must be installed according to
the maximum flue gas temperature and the vent
manufacturer’s instructions.
CPVC, sch 40 ANSI/ASTM F441
Polypropylene
Pending APPROVAL
ULC S636 Class 2C
Table 6. Required Exhaust Vent Material