BRUEL & KJAER PULSE 7788 Скачать руководство пользователя страница 33

Страница: 33 / 62

CHAPTER

Installing

Multi

‐

vehicle

Configuration

Fig.5.10

Connecting

the

LAN

cable

the

front

end

4) Switch the PoE output to the socket used.
5) The base of the WLAN antenna is magnetic. Mount it securely on the roof or an

appropriate external surface of the vehicle. The antenna must be mounted vertically.

6) Ensure that the WLAN unit is securely mounted within the vehicle.
7) Connect the PC to the front end frame using a Cat. 6 LAN patch cable. The PoE should

not be active for this connection.

Fig.5.11

Connecting

the

LAN

cable

the

front

end

8) Switch on the Vehicle Station using the Mains On/Off switch at the rear of the frame.

Connect

the

LAN

cable

the

LAN

socket

Connect

the

LAN

cable

the

LAN

socket
Note:

You

may

have

remove

socket

cover

Содержание PULSE 7788































































Результаты поиска

Содержание PULSE 7788

Отзывы:

Похожие инструкции для PULSE 7788

Бренды по названию

Популярные бренды

BRUEL & KJAER PULSE 7788, Техническая документация инструкция

Результаты поиска

Содержание PULSE 7788

Отзывы:

Похожие инструкции для PULSE 7788

Бренды по названию

Популярные бренды