manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Руководство по обслуживанию

Поделиться
Скачать
Brother MFC 5890CN - Color Inkjet - All-in-One Скачать руководство пользователя страница 80

3-29

Confidential

[ 4 ]

Power transmission route to the head maintenance mechanism and motor rotational 
direction

This mechanism draws its power from two motors--the ASF motor (DC motor) in the right rear
corner of the engine chassis and the paper feed motor (DC motor) on the left side. The ASF
motor is mounted in the ASF motor holder combined with the maintenance unit.

ASF motor 

→

 Maintenance unit (head capping and carriage lock mechanisms)

As shown on the next page, the rotational torque of the ASF motor is always transmitted via the
ASF/maintenance drive gear and idle gear 16 to the clutch gear L.

When the mode switching lever is in the left position (ASF mode), the clutch gear L also
meshes with the ASF changeover gear.

When the head/carriage unit moves to the right end of its travel, a tab on the carriage rear panel
pushes the mode switching lever to the right (purge mode). The clutch gear spring pushes the
clutch gear L to the right, away from the ASF changeover gear, to mesh with the cap lift cam
gear. This way, the ASF motor drives the head capping and carriage lock mechanisms. (See

page 3-31

 for the related components.)

Paper feed motor 

→

 Maintenance unit (purge, air removing and head wiper mechanisms)

As shown on the next page, the paper feed motor drives the PF roller gear L that rotates the
paper feed roller. At the right end of the roller is the PF roller gear R that always meshes with
the clutch gear R.

When the mode switching lever is in the left position (ASF mode), the clutch gear R does not
mesh with the purge gear but it is just idling.

When the head/carriage unit moves to the right end of its travel, a tab on the carriage rear panel
pushes the mode switching lever to the right (purge mode). The clutch gear spring pushes the
clutch gear R to the right to mesh with the purge gear.

As the paper feed motor rotates counterclockwise, the planetary arm meshes with the purge cam
(as shown below), driving the purge mechanism (pump switching unit), air removing
mechanism and head wiper mechanism. On the contrary, the clockwise motor rotation causes
the planetary arm to mesh with the tube pump gear, driving the purge mechanism (tube pump).
(See 

page 3-31

 for the related components.)

Cap lift cam switch

Tube pump

Planetary arm

Air vent tube

Main drain tube

Black drain tube

Purge cam switch

Color drain tube

Pump switching unit

Purge cam

Cap lift cam gear

ASF changeover gear

(3_20)

Содержание MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды