manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Руководство по обслуживанию

Поделиться
Скачать
Brother MFC 5890CN - Color Inkjet - All-in-One Скачать руководство пользователя страница 190

6-35

Confidential

6.1.8 Ink Cartridge Cover and Media Module Cover

(1) Open the ink cartridge cover fully, warp its center upward as shown below, pull its left edge

to release the left boss from the lower cover and then remove the ink cartridge cover.

(2) Release the left and right lock arms of the media module cover and pull the cover to the

front.

Assembling Note:  

When mounting the ink cartridge cover, first insert the cover arm into

the slit provided in the right side of the lower cover and fit the right boss into the right hole
in the lower cover. Then warp the center of the ink cartridge cover upward as shown above
and fit the left boss into the left hole.

Slit

Lock arm

Cover arm

Boss

Boss

Lower cover

Lock arm

Media module cover

Ink cartridge cover

(6_38)

Boss

Retainer

Содержание MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды