manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Руководство по обслуживанию

Поделиться
Скачать
Brother MFC 5890CN - Color Inkjet - All-in-One Скачать руководство пользователя страница 105

4-7

Confidential

[ 2 ] Error codes contained in "MACHINE ERROR X X" messages

Using Function code 82 (described in

 Chapter 9, Section 9.4.28

) displays the most recent error

in the format of "MACHINE ERROR XX." The XX represents one of the error codes listed in
this section.

Note:

 When checking a PCB as instructed in the "Solution" column, also check its harness.

Note: 

To check sensors, use Function code 32 described in 

Chapter 9, Section 9.4.9

 (that is,

press the 

3

 and 

2

 keys in the maintenance mode).

Error Code 

(Hex)

Symptom

Probable Cause

Solution

20
21
22
23

Cannot identify the ink 
cartridge loaded because 
the signal values 
detected by the 
corresponding ink empty 
sensor and ink cartridge 
detection sensor are 
different from the 
specified values.

Ink cartridge not loaded 
correctly

20: Black ink
21: Yellow ink
22: Cyan ink
23: Magenta ink

- Ink cartridge loaded after 

the ink cartridge cover has 
been left open for 10 min-
utes or more

- Ink cartridge replaced 

when the power is OFF

- Ink cartridge loaded very 

quickly

- Ink cartridge halfway 

taken in and out

Reload the corresponding ink 
cartridge.

Ink cartridge partially broken Replace the ink cartridge.

The ink cartridge loaded is 
not the specified one

Load the specified ink 
cartridge.

Ink empty sensor defective

Replace the ink refill ASSY.

Ink empty sensor PCB 
defective

Main PCB defective

Replace the main PCB.

24, 25

Not used.

Содержание MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды