Brother MFC 5890CN - Color Inkjet - All-in-One Скачать руководство пользователя страница 312

Страница: 312 / 448

9-20

Confidential

Given below is the relationship between the LCD indication, sensor name and sensor
status.

The "CR" is always displayed even on models not equipped with a carriage motor driver
thermistor.

(2) Change the detecting conditions (e.g., open the scanner cover or insert paper through the

registration sensor or remove the ink cartridges), and then check that the indication on the
LCD changes according to the sensor states.

(3) To stop this operation and return the machine to the initial stage of the maintenance mode,

press the

Stop/Exit

key.

9.4.10 Printout of Dial Log

(Function code 37) (User-accessible)

Function

The machine prints out a list of telephone numbers dialed.

Operating Procedure

(1) Press the

and

keys in this order in the initial stage of the maintenance mode.

The machine displays the "PRINTING" on the LCD and prints out a list of telephone
numbers that the machine has dialed.

LCD

Sensors

Sensing status

Document front sensor

No document detected.

Document rear sensor

No document detected.

Scanner cover sensor

Scanner cover closed.

Registration sensor

No recording paper detected.

Ink cartridge cover sensor

Ink cartridge cover closed.

Purge cam switch

Any of the cam driving positions

Cap lift cam switch

Any of the cam driving positions

Black ink cartridge detection sensor

Black ink cartridge loaded.

Yellow ink cartridge detection sensor

Yellow ink cartridge loaded.

Cyan ink cartridge detection sensor

Cyan ink cartridge loaded.

Magenta ink cartridge detection sensor

Magenta ink cartridge loaded.

Black ink empty sensor

Black ink remaining

Yellow ink empty sensor

Yellow ink remaining

Cyan ink empty sensor

Cyan ink remaining

Magenta ink empty sensor

Magenta ink remaining

Head thermistor

Driver chip temperature within the
allowable range.

Carriage motor driver thermistor*

Normal temperature detected.

Casing internal temperature thermistor

Normal temperature detected.

Содержание MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды

Brother MFC 5890CN - Color Inkjet - All-in-One, Руководство по обслуживанию

Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды