Brother MFC 5890CN - Color Inkjet - All-in-One Скачать руководство пользователя страница 268

Страница: 268 / 448

7-21

Confidential

[ 7 ] Adjust margins in borderless printing (Function code 66)

Before starting the operation below, be sure to set A4-size paper in the paper tray for printing
check patterns.

(1) On the PC, run "filedg32.exe" in the folder created in

Section 7.1.1

The Filedrgs window appears as shown below.

Left and right margin adjustment

(2) Drag and drop the "media.prn" onto the Brother Maintenance USB Printer driver icon in

the Filedrgs window shown above.

The machine displays the "RECEIVING DATA" on the LCD and prints out the "MEDIA
CHECK" pattern (see

page 7-24

for a sample printout). This is for checking the left and

right margins.

(3) Measure the left and right margins on the printed pattern.

The upper row is printed in 600 dpi, and the lower row, in 1200 dpi.

(Example) 600 dpi

Left: 0.8 mm, Right: 1.1 mm

1200 dpi Left: 0.9 mm, Right: 1.2 mm

If both of the left and right margins are within the range from 0.9 to 1.1 mm, no adjustment
is required. If not, go to step (4).

(4) If either of the left and right margins is out of the specified range, press the

key twice and

the

key on the machine.

The "LEFT: 10" appears on the LCD.

Содержание MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды

Brother MFC 5890CN - Color Inkjet - All-in-One, Руководство по обслуживанию

Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды