Brother MFC 5890CN - Color Inkjet - All-in-One Скачать руководство пользователя страница 259

Страница: 259 / 448

7-12

Confidential

[ 4 ] Correct the positioning error of the head/carriage unit

Before starting the operation below, be sure to set A4-size paper in the paper tray for printing
check patterns.

(1) Run "filedg32.exe" in the folder created.

The Filedrgs window appears as shown below.

(2) Drag and drop the "incline.prn" icon onto the Brother Maintenance USB Printer driver icon

in the Filedrgs window shown above.

The machine displays the "RECEIVING DATA" on the LCD and prints out the "Incline
Adjust" test pattern shown on the next page.

(3) Out of the three rows of the "Incline Adjust" test pattern (on the next page), check the

middle row and select the block that is the least uneven print. Make a note of that block
number.

Содержание MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды

Brother MFC 5890CN - Color Inkjet - All-in-One, Руководство по обслуживанию

Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды