Brother HL-1070 - B/W Laser Printer Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 244

background image

IV-27

6.

INSPECTION MODE

6.1

Incorporated Inspection Modes

The printer incorporates various inspection modes such as the factory inspection mode
and the test print mode. The inspection mode varies depending on the model of the
printer.

This printer supports a factory inspection mode, continuous grid pattern print mode, 3
patterns print mode and NV-RAM value dump mode.

The operation of the inspection mode is as follows.

(1)

Turn off the power switch of the printer.

(2)

With the top cover open, turn on the power switch while holding down
the switch on the control panel.

When you enter this inspection mode, the Drum lamp is ON. Holding down the
panel switch will cause the lamps turn ON in the order Drum

Alarm

Ready

Data

Drum. When you release the switch, a mode is selected.

The mode selected is indicated by the lamp which is ON when you release the
switch.

The inspection modes are assigned to the respective lamps as shown below.

Lamp

Type of inspection

Drum

Factory inspection mode

Alarm

Continuous grid pattern print mode

Ready

3 patterns print mode (grid

zip

black)

Data

NV-RAM value dump mode

Drum + Alarm

ROM code reprogramming mode (only
when the flash memory is fitted)

Alarm + Ready

RAM check

Ready + Data

4% density pattern print mode

Details of the factory inspection mode are as follows.

This mode is used to check if the sensors in the printer are functioning correctly. In the
process of this inspection, the lamps and the switch on the control panel are also
checked. On entering this mode, the lamps show the status of the respective sensors as
follows.

«
...
89
90
91
92
93
...
»

Содержание HL-1070 - B/W Laser Printer





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-1070 - B/W Laser Printer

Бренд: Panasonic Страницы: 2

Бренд: Xerox Страницы: 168

Бренд: Xerox Страницы: 36

Бренд: Xerox Страницы: 64

Бренд: Xerox Страницы: 54

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 115

Бренд: Oki Страницы: 152

Бренд: Oki Страницы: 140

Бренд: Oki Страницы: 181

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 229

Бренд: Oki Страницы: 224

Бренд: Oki Страницы: 141

Бренд: Oki Страницы: 160

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды