Brother HL-1070 - B/W Laser Printer Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 244

background image

USER’S GUIDE

3–6

✒

Note

To set the Page Protection to A4, Letter or Legal paper sizes, the
following total capacity of memory is required.

300 dpi 600 dpi

Letter/A4 2 Mbytes 6 Mbytes
Legal 3 Mbytes 6 Mbytes

If your printer does not have enough memory for page protection, your
document may be printed at 300 dpi.

You can set this function in the following ways.
The supplied printer driver for Windows 95/98/3.1

The supplied RPC program for DOS
For details of the settings, see the relevant help screen.

APT (Advanced Photoscale Technology)

APT allows your printer to produce fine gray scales to improve the
appearance of documents containing photographic images.
Using this feature, the image is printed in 256 shades of gray at near
photographic quality.

This setting can be made by using the supplied Windows driver. Also, a
demo file which can be opened within Windows Write is included on the
supplied disk. Try printing it with the APT feature.

For details of the settings, see the relevant help screen of the RPC or
Windows driver.

✒

Note

APT is a simpler feature than 1200 x 600 dpi for Windows DIB graphics.
APT does not required so much memory as the 1200 x 600 dpi resolution
setting.

«
...
186
187
188
189
190
...
»

Содержание HL-1070 - B/W Laser Printer





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-1070 - B/W Laser Printer

Бренд: Oki Страницы: 33

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 11

Бренд: OKIDATA Страницы: 58

Бренд: 3D Systems Страницы: 17

Бренд: 3D Systems Страницы: 8

Бренд: 3D Printing Systems Страницы: 54

Бренд: DataCard Страницы: 2

Pixma TS7700i Series

Бренд: Canon Страницы: 554

Бренд: Flashforge Страницы: 36

Бренд: Intermec Страницы: 38

MP 2554SP Series

Бренд: Ricoh Страницы: 1

Бренд: Mitsubishi Страницы: 86

B-470-QQ Series

Бренд: TEC Страницы: 32

Бренд: Anet Страницы: 36

Screen Truepress Jet520 Series

Бренд: Konica Minolta Страницы: 4

Бренд: Konica Minolta Страницы: 8

Бренд: Savin Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды