Brother HL-1070 - B/W Laser Printer Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 244

background image

USER’S GUIDE

3–4

Other Control Features

The printer has the following useful features:

Sleep Mode

When the printer does not receive data for a certain period of time (time-
out), it enters sleep mode. Sleep mode acts as though the printer was
turned off. The default time-out is 5 minutes. While the printer is in sleep
mode, all the lamps are off and it is as if it was turned off, but the printer
can still receive data from the computer. Receiving a print file or
document automatically wakes up the printer to start printing. Pressing
the

switch

also wakes up the printer.

✒

Note

When the printer goes into sleep mode, the fan will not stop until the

printer engine has cooled down.

Sleep mode allows the print engine to cool, so the temperature of your

room and how long the printer has been in sleep mode affects the
warm-up time. This warm-up time can take up to 30 seconds. The

Ready

lamp blinks to indicate that the printer is warming up.

You can change the time out for the sleep mode with the supplied

printer driver or Remote Printer Console program. Refer to the Help
section in the printer driver or RPC program for more information
about the sleep mode setting.

Test Print Mode

The printer has the following test print mode. Follow these steps:

1. Make sure that the top cover is closed.

2. Hold down the switch and turn on the power switch. Keep the

switch

depressed until the

Drum

lamp comes on.

The

Drum

lamp lights to indicate that the printer is in the test print

mode.

3. Press the

switch

again to execute the test print or hold down the

switch

to select another option and release the

switch

to execute the

selected option.

The test print mode varies depending upon the printer model as
follows:

«
...
184
185
186
187
188
...
»

Содержание HL-1070 - B/W Laser Printer





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-1070 - B/W Laser Printer

870 - SuperScript B/W Laser Printer

Бренд: NEC Страницы: 52

SuperScript 1800

Бренд: NEC Страницы: 8

Бренд: Samsung Страницы: 165

Бренд: Samsung Страницы: 2

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 155

CLX-3170FN series

Бренд: Samsung Страницы: 220

CLX 6210FX - Color Laser - All-in-One

Бренд: Samsung Страницы: 36

CLX-3160 Series

Бренд: Samsung Страницы: 139

Бренд: Samsung Страницы: 8

Lazett Combo SCX-4016

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 319

Бренд: Olivetti Страницы: 2

Бренд: Olivetti Страницы: 109

Бренд: Olivetti Страницы: 111

Бренд: Olivetti Страницы: 8

WorkCentre 7232

Бренд: Xerox Страницы: 13

CX PRINT SERVER 550

Бренд: Xerox Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды