Brother HL-1070 - B/W Laser Printer Скачать руководство пользователя страница 140

Страница: 140 / 244

- 10 -

Insert the supplied CD-ROM into the
drive of your PC.

Select “CD-ROM drive.”

Click the

Next

button.

Click the

Next

button.

The USB driver is installed.

When the dialog shown above appears on
your PC, click the

Finish

button.

Be sure to restart Windows 98 so that
the installed USB driver will be
effective.

When the installation of the USB driver is complete, install the printer driver.

From CD-ROM:

Run the CD-ROM program and go to the ‘Install driver’ menu.

From Floppy disk:

Refer to the Software Quick Setup Guide.

Set the printer port to USB

After installing the USB driver and printer driver, the printer port has to be set to ‘USB port’.
1. Click the

Start

button and select

Printers

Settings

2. Select the HL-1070 icon in printers so that the HL-1070 icon is highlighted.
3. Select

Properties

from

File

menu.

4. Click

Details

tab.

5. Select

BRUSB

:(USB Printer Port) in the box for “Print to the following port”.

6. Click

to close the properties dialog box.

Содержание HL-1070 - B/W Laser Printer





















































































































































































































































Результаты поиска

Содержание HL-1070 - B/W Laser Printer

Отзывы:

Похожие инструкции для HL-1070 - B/W Laser Printer

Бренды по названию

Популярные бренды

Brother HL-1070 - B/W Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание HL-1070 - B/W Laser Printer

Отзывы:

Похожие инструкции для HL-1070 - B/W Laser Printer

Бренды по названию

Популярные бренды