Brother HL-1070 - B/W Laser Printer Скачать руководство пользователя страница 76

Страница: 76 / 244

IV-12

I-11

Poor fixing

Possible cause

Step

Check

Result

Remedy

Printing paper

Is thick paper more than 36lb
weight in use?

Yes

Instruct the user to use paper
of the recommended weight
and thickness.

Toner sensing
failure

Is the problem solved by
replacing the drum unit or the
toner cartridge?

(When printing is faint.)

Yes

Toner is empty.

The toner sensing is defective,
clean the toner sensor.

If the wiper in the toner
cartridge is broken, replace the
toner cartridge with a new one.

Thermistor
failure

Is the thermistor fitted
correctly?

Fit the thermistor correctly.

Low-voltage
power supply
PCB failure

Is the problem solved by
replacing the low-voltage
power supply PCB?

Yes

Replace the low-voltage power
supply PCB.

I-12

Image distortion

Possible cause

Step

Check

Result

Remedy

Scanner

Is the scanner unit secured to
the frame incorrectly?

Is there any play?

Yes

Secure the unit correctly and
tighten the screws.

Scanner LD
emission failure

Scanner motor
rotation failure

Is the laser diode or the laser
scanner motor defective?

Yes

Replace the scanner unit.

Scanner
connection
failure

Is the scanner harness
connected properly?

Is it coming loose?

Yes

Connect the harness correctly.

Содержание HL-1070 - B/W Laser Printer





















































































































































































































































Результаты поиска

Содержание HL-1070 - B/W Laser Printer

Отзывы:

Похожие инструкции для HL-1070 - B/W Laser Printer

Бренды по названию

Популярные бренды

Brother HL-1070 - B/W Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание HL-1070 - B/W Laser Printer

Отзывы:

Похожие инструкции для HL-1070 - B/W Laser Printer

Бренды по названию

Популярные бренды