background image

2

Section 1 Introduction

 

Product Support  References

Refer to www.BrooksInstrument.com for Brooks sales and service
locations and to obtain other documents that support the GF100 Series.
Those documents include:

-

Brooks MultiFlo

TM

 Configurator Quick Start Manual:

X-SW-MultiFlo-Config-QS-eng. part Number 541B167AAG

-

Brooks GF100 Series data sheets:

DS-TMF-GF100-Series-MFC-eng
DS-TMF-GF135-Series-MFC-eng
DS-TMF-GF121-Series-MFC-eng
DS-DPT-EtherCAT-GF100-Series-eng

Notice and Caution Statements

Warning, caution and notice statements are located throughout this manual
in the ANSI format. A WARNING statement indicates a potentially
hazardous situation which, if not avoided, COULD result in death or serious
injury.  A CAUTION statement indicates a potentially hazardous situation
which, if not avoided, MAY result in minor or moderate injury. It may also be
used to alert against unsafe practices. A NOTICE statement describes
specific information that requires special attention.

Product Warranty

Product warranty information can be found on the Back Cover of this
Manual and on the Brooks website at 

www.BrooksInstrument.com

. This

information provides general warranty information, limitations, disclaimers,
and applicable warranty periods according to product group.

How to Order a GF100 Series Device

Refer to Section 5.

Industry Standard References

Refer to Table 1-1.

GF100 Series Gas Table

Refer to Appendix A.

Glossary of Terms and Acronyms

Refer to Table 1-2

Содержание GF135
































































Отзывы: