BRONKHORST Mini CORI-FLOW MI Series страница 14 Скачать руководство пользователя

Страница: 14 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

2.4.1.4

EtherCAT/PROFINET

Connection terminals:

Fieldbus (RJ-45)

D Display

M Main

Actuator

Valve

Fuses:

main

actuator

2.5

Optional fieldbus interface

FLOW-BUS

FLOW-BUS is a Bronkhorst® designed fieldbus, based on RS485 technology, for digital communication between devices,

offering the possibility of host-control by a Windows computer.

Characteristics:

Baud rate 187500 (default) or 400000 Baud

+15…24 Vdc supply voltage

Easy installation and communication with other Bronkhorst® devices

Automatic node search and bus optimization (gap fixing)

RS232 communication (

ProPar

) with Windows computer (local host)

Connection of up to 120 instruments on a single bus

Maximum bus length: 600 m

Consult

Instruction manual FLOW-BUS interface

(document no. 9.17.024) for more information about setting up a

FLOW-BUS network.

See also section

Bus termination switches

for information about the built-in bus termination resistor.

Modbus

Modbus is a 3-wire, RS485-based fieldbus communication system for parameter value exchange. In this system each

instrument/device is equipped with a micro-controller for its own dedicated task. The instrument behaves as a slave, which

means all communication (instructions and readout) is initiated by a master device on the Modbus system.

Characteristics:

Baud rate selectable between 9600 and 256000 Baud (default: 19200 Baud)

+15…24 Vdc supply voltage

Connection of up to 247 instruments on a single bus

Supports RTU and ASCII protocols

Consult

Instruction manual Modbus interface

(document no. 9.17.035) for more information about setting up a

Modbus network.

See also section

Bus termination switches

for information about the built-in bus termination resistor.

Содержание Mini CORI-FLOW MI Series






















































Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды

BRONKHORST Mini CORI-FLOW MI Series, Инструкция по эксплуатации

Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды