BRONKHORST Mini CORI-FLOW MI Series страница 17 Скачать руководство пользователя

Страница: 17 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

To avoid simultaneous heating and cooling of different parts of the instrument, make sure the ambient temperature is

as stable and evenly distributed across the environment as possible.

Avoid temperature shocks; heating or cooling should amount to no more than 1 °C per second.

Make sure that the media temperature matches the ambient temperature as closely as possible.

The mini CORI-FLOW™ will show an amount of self heating, due to power dissipation of the electronics. This effect can

be as large as approximately 15 °C (depending on media and ambient temperature). In practice, there will be a balance

between media temperature, self heating and ambient temperature.

Operation in a cool environment can compensate somewhat for the effect of high media temperatures.

Heating and cooling effects will also depend on the cooling/heat conducting capacities of the installation itself on which

the instrument is mounted.

Make sure the temperature in the housing does not exceed 70°C, otherwise the electronics might get damaged. To check

this, the internal temperature output can be used (parameter

Temperature

, e.g., via FlowDDE or a readout and control

unit (E-8000 or BRIGHT)).

3.6

Communication

The following table lists the supported communication modes of the mini CORI-FLOW™:

Connection

Type

Communication standard

Fieldbus/protocol

Main terminal

Analog

0…5Vdc

0…10Vdc

0…20mA

4…20mA

n/a

Digital

RS232

ProPar

RS485

FLOW-BUS

Modbus (RTU/ASCII)

HART

Fieldbus terminal

Digital

RS485

FLOW-BUS

Modbus (RTU/ASCII)

PROFIBUS DP

Ethernet

PROFINET

EtherCAT®

The communication standards (analog and digital) and fieldbus interface (if applicable) are specified at ordering time, i.e.:

In analog mode, the instrument is set to the specified voltage/current range

The dedicated fieldbus connection only provides the specified fieldbus interface

Using analog and digital interfaces simultaneously

The instrument can be operated via the analog and the digital interface at the same time; analog signals and digital

parameters can be read (or changed) simultaneously. The instrument accepts a setpoint from either the analog or any of the

digital interfaces (this is called the control mode; see

Special parameters

for more information). In analog mode, the analog

input and output signals are translated to the digital setpoint and measure parameter respectively. The default control

mode (analog or digital) is selected at ordering time.

3.6.1

Analog operation

With analog operation the following signals are available:

output signal: measured value

input signal: setpoint (controller only)

Setpoints below 2% of the full scale will be interpreted as 0%.

Содержание Mini CORI-FLOW MI Series






















































Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды

BRONKHORST Mini CORI-FLOW MI Series, Инструкция по эксплуатации

Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды