BRONKHORST Mini CORI-FLOW MI Series страница 15 Скачать руководство пользователя

Страница: 15 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

PROFIBUS DP

PROFIBUS DP is a 2-wire, RS485-based industrial data communication standard (fieldbus) which allows automation

components (e.g. sensors, actuators and controllers) to exchange information.

Consult

Instruction manual PROFIBUS DP interface

(document no. 9.17.025) for more information about setting up a

PROFIBUS DP network.

See also section

Bus termination switches

for information about the built-in bus termination resistor.

EtherCAT®

Ethernet for Control Automation Technology (EtherCAT®) is an open high performance Ethernet based fieldbus system.

Consult

Instruction manual EtherCAT® interface

(document no. 9.17.063) for more information about setting up an

EtherCAT® network.

PROFINET

The PROFINET interface is 100% Ethernet compatible and is used for data exchange between I/O controllers (PLC, etc.) and

I/O devices (slaves, field devices). PROFINET uses the proven communication model and application view of PROFIBUS DP.

Consult

Instruction manual PROFINET interface

(document no. 9.17.095) for more information about setting up a

PROFINET network.

HART

HART is a bi-directional communication protocol, owned by the FieldComm Group, for sending and receiving digital

information across the 4…20 mA analog current loops that connect the vast majority of field instruments with distributed

control systems. HART technology offers a reliable solution for plant operators who seek the benefits of digital

communication, while preserving existing analog instrumentation and plant wiring.

Characteristics:

Baud rate: 1200 baud

Easy remote access to digital functionality of instrument over analog wiring

Digital communication across 4…20 mA analog output

Detailed information about the HART protocol can be found on the FieldComm website:

www.fieldcommgroup.org

Содержание Mini CORI-FLOW MI Series






















































Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды

BRONKHORST Mini CORI-FLOW MI Series, Инструкция по эксплуатации

Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды