BRONKHORST EL-PRESS Metal sealed Скачать руководство пользователя

Страница: 30 / 45

Bronkhorst®

Instruction Manual EL-PRESS™

9.17.101I

Digital parameters

This section describes the most commonly used parameters for digital operation of the EL-PRESS™. Descriptions are

grouped by category in tables as shown below:

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

[type]



[x]…[y]

[DDE par]

[Pro]/[Par]

[address]/[register]

In this manual, parameter names are printed in italics (reverted to

normal

where embedded in italics, like in this tip).

Type

Unsigned char

1 byte unsigned integer (0…255)

Unsigned int

2 byte unsigned integer, MSB first (0…65535)

Unsigned long

4 byte unsigned integer, MSB first (0…4294967295)

Float

4 byte floating point, IEEE 32-bit single precision, MSB first

Unsigned char [x] x byte array (text string)

Access

Parameter value can be read

Parameter value can be written



Parameter is secured and only accepts values if parameter

Init Reset

is set to 'unlocked' first

Range

Some parameters only accept values within a certain range:

[x]

Minimum value of the range

[y]

Maximum value of the range

FlowDDE

Parameter number within FlowDDE

FLOW-BUS

Within the FLOW-BUS protocol (ProPar when using RS-232 communication), parameters are identified by a unique

combination of a process number and a parameter number:

[Pro]

Process number

[Par]

Parameter number

Consult the

RS-232 manual

(document no. 9.17.027) for detailed information.

Modbus

In the Modbus protocol, parameters are accessed by specifying their unique decimal register number or corresponding PDU

address (Protocol Data Unit). The PDU address is the hexadecimal translation of the register number minus 1, e.g. register

number 1 corresponds to PDU address 0x0000, register number 11 corresponds to PDU address 0x000A:

[address]

Hexadecimal PDU address

[register]

Decimal register number

Modbus address blocks are two bytes big. Larger data types use up to 8 subsequent address blocks, resulting in a

maximum variable length of 16 bytes. Values longer than the maximum length are truncated.

Other interface protocols

Consult the specific fieldbus manual for accessing parameters using fieldbus communication (see

Documentation

Содержание EL-PRESS Metal sealed














































Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды

BRONKHORST EL-PRESS Metal sealed, Инструкция по эксплуатации

Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды