BRONKHORST EL-PRESS Metal sealed Скачать руководство пользователя

Страница: 35 / 45

Bronkhorst®

Instruction Manual EL-PRESS™

9.17.101I

Serial Number

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[20]



113/3

0xF118…0xF11F/ 61721…61728

Instrument serial number for identification.

BHT Model Number

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[35]



113/2

0xF110…0xF117/ 61713…61720

This parameter shows the Bronkhorst® instrument model type information.

Firmware Version

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[6]

105

113/5

0xF128…0xF12A/ 61737…61739

Revision number of the firmware

Identification Number

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char



0…255

175

113/12

0x0E2C/3629

Bronkhorst® (digital) device type identification number.

Device Type

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[6]

113/1

0xF108…0xF10A/ 61705…61707

Device type information string; this parameter contains an abbreviation referring to the identification number.

4.4

Alarms

Alarm settings are most easily accessible using FlowPlot or FlowView or a Bronkhorst® readout and control unit.

The built-in alarm functionality can be used to handle different alarm types:

system errors and warnings

min/max alarms

response alarms

batch alarms

master/slave alarms

The used alarm type can be set with parameter

Alarm Mode

. When an alarm is activated, the type can be read out using

parameter

Alarm Info

. An automatic setpoint change can be set using the parameters

Alarm Setpoint Mode

and

Alarm New

Setpoint

. It is also possible to set an alarm delay, to prevent overreaction to small disturbances, using parameter

Alarm Delay

Time

. The methods by which an alarm can be reset are controlled by

Reset Alarm Enable

Содержание EL-PRESS Metal sealed














































Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды

BRONKHORST EL-PRESS Metal sealed, Инструкция по эксплуатации

Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды