background image

16

  5.2  Care of the lithium battery
 

   During charging and discharging, the ambient temperature should be in the range +5 °C to +35 °C. 

Use of the battery at very low temperatures may result in a severe loss of output.

 

   The battery has a deep-sleep mode and switches itself off after 72 hours unless it is inserted into 

a power pack so as to protect it against deep discharge. In this way the energy stored in the battery 
is retained even after months without use.

 

   To wake up the battery after 72 hours without use, press the "on" key on the battery’s front panel.

 

   The type of battery used does not have a "memory effect", and so does not have to be discharged 

regularly. It is, however, important to remember that the battery must not be discharged too far. 

The unit switches off automatically when the battery voltage is too low. However, because there is a 

small leakage current even when the unit is switched off, we strongly recommend that the battery 
is recharged after use. The battery should be removed from the unit during long periods out of use.

 

   In particular, please observe the following important information on the subject of care and main-

tenance of the battery:

 

   Important note: before the first startup, we recommend that you charge the battery. We also 

recommend that you recharge the battery immediately after use, even if it is only partially dis-
charged. Avoid discharging the battery completely!

 

   You will find further information on care of the battery on our website under 

 

  "Download" > "battery & care".

  5.3.  Charging the battery
 

   The battery can be charged either installed in the unit or outside it. The unit can be operated while 

it is charging.

Содержание Move 1200 L RFS 2





























Отзывы: