Broncolor Move 1200 L RFS 2, Руководство по эксплуатации

Страница: 23 / 28

25
15. MOBILED
The MobiLED lamp was developed to suit the Move 1200 L RFS 2
power pack: exceptionally compact and light, MobiLED has a
tilt-and-swivel head for single-handed operation and an in-
tegral reflector mounting. The intelligent ventilation control
only switches on when the operating temperature demands
it. The unique design requires very little space for transport
and storage.
The continuous operation mode of the Move 1200 L RFS 2
enables the use of powerful LEDs for modelling light so
as to create new light design effects. Especially at the day-
light colour temperature of 5500 K, it offers completely new
possibilities for film sequences.
Important note: all MobiLED lamps with the serial numbers N08, N10, N12 and O04 must be
modified in our Service Centre before use with the Move 1200 L RFS 2 power pack.
15.1 Replacing flash tubes
Before you change the flash tube, be sure to disconnect the lamp from the power pack! Plug-in
flash tubes are used.
To change a flash tube, remove the snap ring and take out the protecting glass. Then pull the flash
tube axially out of its socket. When replacing the flash tube make sure it is pushed in as far as it
will go. Finally replace the protecting glass and secure it with the snap ring. Protecting glasses are
available in the versions "UVE" art. no. 34.339.00 (5500 K) and "UVE matt" art. no. 34.340.00 (5500 K).
15.2 Lamp plugs
Lamp plugs and connections are fitted with mechanical interlocks to prevent unintentional dis-
connection. To unplug, push down the locking spring below the cable guide and pull the plug out
of its socket.
15.3 Extension cable to MobiLED
The extension cable (3.5 m / 11.5 ft), available as an accessory under art. no. 34.150.00, is espe-
cially thin and flexible. It is only intended for use with MobiLED, Mobilite and Mobilite 2. If the cable
is used with other lights, the modelling light and cooling fan will not operate.
15.4 Lamp fuses
Use only sand-filled fuses of the type indicated on the type plate!
Max. energy Move 1200 L RFS 2 Comments
Mobilite
Mobilite 2 1600 J x
x Modification required (Service)
Modification required (Service)
MobiLED 1600 J x Modification required (Service)
for serial numbers:
N08, N10, N12, O04
Litos 2400 J -
Picolite 1600 J x* Flash yes, modelling light no
Primo 1600 J
Pulso F2 / Hazy 2 1600 J x* Flash yes, modelling light no
Pulso G 1600 J
Unilite 1600 J 1600 J x* Flash yes, modelling light no
Pulso G 3200 J
Unilite 3200 J 3200 J x* Flash yes, modelling light no
Pulso F4 / Hazy 4 3200 J x* Flash yes, modelling light no
Pulso Twin 2 x 3200 J x* Flash yes, modelling light no
Primo 3200 J x* Flash yes, modelling light no
Lightbar
Striplite 3200 J
3200 J x* Flash yes, modelling light no
Pulso Spot 4 3200 J x* Flash yes, modelling light no
Ringflash C
Ringflash P 3200 J
3200 J x* Flash yes, modelling light no
Litestick 3200 J x*
Boxlite 40 (A3) 3200 J x* Flash yes, modelling light no
No. of flashes per sequence is
limited (see marking on lamps!)
Pulso 8 / Hazy 8 6400 J -