background image

Page 1

MODEL 757SNC 

WARNING  

 

TO REDUCE THE RISK OF FIRE, ELECTRIC 
S H O C K ,  O R   I N J U RY  TO   P E R S O N S , 
OBSERVE THE  FOLLOWING:

1.  Use this unit only in the manner intended by the 

manufacturer. If you have questions, contact the 
manufacturer at the address or telephone number 
listed in the warranty.

2.  Before servicing or cleaning unit, switch power off 

at service panel and lock the service disconnecting 
means to prevent power from being switched on 
accidentally. When the service disconnecting means 
cannot be locked, securely fasten a prominent 
warning device, such as a tag, to the service panel.

3.  Installation work and electrical wiring must be 

done by qualified personnel in accordance with 
all applicable codes and standards, including 
fi re-rated construction codes and standards.

4.  Suffi cient air is needed for proper combustion and 

exhausting of gases through the fl ue (chimney) of fuel 
burning equipment to prevent backdrafting. Follow the 
heating equipment manufacturer’s guideline and safety 
standards such as those published by the National 
Fire Protection Association (NFPA), and the American 
Society for Heating, Refrigeration and Air Conditioning 
Engineers (ASHRAE), and the local code authorities.

5.  When cutting or drilling into wall or ceiling, do not 

damage electrical wiring and other hidden utilities.

6.  Ducted fans must always be vented to the outdoors.
7.  NEVER place a switch where it can be reached from 

a tub or shower.

8.  This unit must be grounded.
9.  This unit is cULus listed. Type I.C. inherently protected.
10. When  applicable local regulations comprise more 

restrictive installation and/or certifi cation requirements, 
the aforementioned requirements prevail on those of 
this document and the installer agrees to conform to 
these at his own expenses.

11. When performing installation, servicing or cleaning 

this unit, it is recommended to wear safety glasses 
and gloves.

CAUTION  

!

1.  For general ventilating use only. Do not use to exhaust 

hazardous or explosive materials and vapors.

2.  This product is designed for installation in FLAT 

CEILINGS ONLY. Do not mount this product in a wall.

3.  The light fi xture assembly must be mounted to the 

fan housing assembly included with this product. 

Do 

not mount the light fi xture assembly to a 
wiring outlet box.

4.  To avoid motor bearing damage and noisy and/or 

unbalanced impellers, keep drywall spray, construction 
dust, etc. off power unit.

5.  Please read specifi cation label on product for  further 

information and requirements.

DECORATIVE
CEILING VENTILATOR

READ AND SAVE THESE INSTRUCTIONS

TYPICAL INSTALLATIONS

HOUSING MOUNTED

TO ADDITIONAL FRAMING

Discharge 90° to joists.

HOUSING MOUNTED

DIRECTLY TO  JOIST

2 x 6 (or larger) 

Discharge parallel to joists.

HOUSING MOUNTED

TO 2 x 4 TRUSS

Requires additional framing

for mounting tabs.

Discharge parallel to joists.

HOUSING MOUNTED TO “

I

” JOIST

Requires additional framing

for mounting tabs.

Discharge parallel to joists.

HOUSING MOUNTED 

TO 2 x 4 TRUSS

Requires additional framing

for mounting tabs.

Discharge 90° to joists.

HOUSING MOUNTED TO “

I

” JOIST

Requires additional framing

for mounting tabs.

Discharge 90° to joists.

Installer: Leave this manual with the homeowner.

Homeowner: Use and Care information on page 4.

*Additional framing must be a 2 x 6 (minimum height), at least 9-inch long.

BB0008

BH0013A

*

BH0012A

BH0015A

*

BH0014A

*

BH0017A

*

BH0016A

*

Register your product 

online at www.broan.ca

Содержание 757SNC









Отзывы: