Broadcom NetXtreme II SERIES Скачать руководство пользователя страница 184

Страница: 184 / 264

Using Broadcom Advanced Control Suite 4: Broadcom NetXtreme II® Network Adapter User Guide

file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/English/bacs.htm[9/5/2014 3:45:16 PM]

IPv4 DHCP

The IP address is from a DHCP server if the value is Enable.

IP Address

The network address associated with the adapter. If the IP address is all 0s, the associated driver has not been bound with Internet

Protocol (IP).

IPv6 DHCP

The IP address is from a DHCP server if the value is Enable.

IPv6 IP Address

The IPv6 network address associated with the adapter.

IPv6 Scope Id

Since local-use addresses can be reused, the Scope ID for link-local addresses specifies the link where the destination is located. The

Scope ID for site-local addresses specifies the site where the destination is located. The Scope ID is relative to the sending host.

IPv6 Flow Info

The non-zero Flow Info is used to classify traffic flows. If Flow Info equals zero, then the packets are not a part of any flow.

Default Gateway

The default gateway value is the network address of the gateway that will be used by the management firmware for packets destined

for hosts external to the local network segment.

Link Status

The status of the network link.

Up.

A link is established.

Down.

A link is not established.

Duplex

The adapter is operating in the indicated duplex mode.

Speed

The link speed of the adapter, in megabits per second.

Offload Capabilities

The offload capabilities supported by the adapter. This information is only available for Broadcom NetXtreme II adapters.

TOE

. TCP Offload Engine (TOE) allows simultaneous operation of up to 1024 fully offloaded TCP connections for 1-Gbps

network adapters and 1880 fully offloaded TCP connections for 10-Gbps network adapters to the hardware.

iSCSI

. iSCSI offload for block-level transfer of data.

LSO

. Large Send Offload (LSO) prevents an upper level protocol such as TCP from breaking a large data packet into a series

of smaller packets with headers appended to them.

CO.

Checksum Offload (CO) allows the TCP/IP/UDP checksums for send and receive traffic to be calculated by the adapter

hardware rather than by the host CPU.

LiveLink IP Address

The network address of the LiveLink enabled adapter.

Local Connection

Identifies the module to which the blade server is attached.

Chassis SW

. Chassis switch module

Содержание NetXtreme II SERIES









































































































































































































































































Результаты поиска

Содержание NetXtreme II SERIES

Отзывы:

Похожие инструкции для NetXtreme II SERIES

Бренды по названию

Популярные бренды

Broadcom NetXtreme II SERIES, Руководство пользователя

Результаты поиска

Содержание NetXtreme II SERIES

Отзывы:

Похожие инструкции для NetXtreme II SERIES

Бренды по названию

Популярные бренды